We are using nRF51822 for our products.
We want to know the min value of "Receiver sensitivity" when we use this chip for BLE.
The Datasheet says "Receiver sensitivity...
Dear
The BLE Multi-link example (ble_app_multilink_central and ble_app_multilink_peripheral)
shows how one central device can connect to multiple peripheral devices. ...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
I have the nRF Control Panel Android application. It works fine with several BLE devices, but specifically for the Fitbit Flex, it fails to connect.
I know Fitbit wristbandes...
Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Previously i've been using the nRF dongle using the BLE NUS Central example to communicate to another nRF DK with the BLE NUS Peripheral example via serial/termite and ble...
Hi there,
I am new to the nRF world and I might be asking a very stupid question with obvious answer but I couldn't find any hint from the Infocenter nor the Tutorials...
Hello guys,
I followed this guide to set up the software on my macbook.
The blinky example can be successfully built, but cannot be flashed to the nRF52 DK. Then I tried...
Hello everyone,
I tried to rename(right click the project name and click the "Rename") my project from "sdk11_ble_tutorial_adverstising" to "sdk11_ble_tutorial_adverstising1...
Hi,
anyone would have any idea (to look at, as to) why the same app running on the same chip/PCB (nrf51822QFAAH rev3) could possibly have slowed down so massively after...
I'm trying to add debug information to ble_app_hrs using nRF5 SDK 10, softdevice s110 version 8.0.0, building for an nRF51-DK target (PCA10028) using ARMGCC. I've found that...
I've encountered a problem getting the tick count from FreeRTOS when tickless idle is enabled. I'm not sure if this is a bug or just unexpected behavior. I am using the latest...
Hi everyone,
I'm integrating the spi_master_with_spi_slave example into our firmware; however, I'm not seeing the event callback I registered being called. I'm verifying...
Hi everyone,
I implemented nrf51 flashing through SWD (external MCU is used). After first flashing and reset when we enter debug mode on SWD second time we have a busy...
Hello,
I am trying to interface an MPU 6050 with an NRF52 with sdk vs 12.0. I noticed in the mpu6050.c file that it uses a twi_master.h file in the sdk in folder labeled...
Linking ble_app_proximity_pca10040_s132.elf
Output/nrf52832_xxaa/Exe/ble_app_proximity_pca10040_s132.elf section `.fs_data' will not fit in region `UNPLACED_SECTIONS'
...
Hi,
I flashed an board with a NRF52832-QFAA-R7 with the ble_app_hids_mouse of SDK 12.1 (and also with the keyboard) example to test and build an application using this...
Hi,
I've been trying to get an implementation of the HTTP Proxy working with nRF52. The nRF52 is in central mode, accessing the proxy (running on a Pi with Bleno) which...
i measured the current of nrf52 dk board with the spi example (examples\peripheral\spi\pca10040). the result shows that it consumed about 6 mA !!!
i read the nrf52 datasheet...
Building ‘ble_app_cscs_pca10040_s132’ from solution ‘ble_app_cscs_pca10040_s132’ in configuration ‘nrf52832_xxaa’
Generating linker script ‘ble_app_cscs_pca10040_s132.ld...
