We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
pin 2 is for turning on and off at sepecified time...
pin 3 is for turning on the light whrn button is pressed and turned off automatically as time decided in the program...
I have been debugging this problem for a few days and have exhausted all of my options. I am relatively new to embedded development so user error is not out of the question...
Hi,
I need to load ble code to mrf51422. I read on the forum that I can do it using nrf51 dk but did not get the steps. Couod someone give me detailed description about...
VPN Solutions are a guaranteed private network association constructed on top of infrastructure that is publicly available. vpn connection free Providers provide an alternative...
Hello to everyone!
I'm digging documentation of SDK. and I meet a lot of doxygen things like this
/**@brief Macro for configuring a pin to use a GPIO IN or PORT EVENT...
Hello Everyone,
I want to program the BMD-300 with the nRF52 Preview Development Kit.
I have connected:
BMD-300 -> nRF52-DK
SWDIO -> SH_SWDIO (pin #4) on P20
...
Sorry for probably stupid question..
All the time in SDK we set need bits through the mask, for example
NRF_GPIOTE->CONFIG[idx] |= (pin << GPIOTE_CONFIG_PSEL_Pos) &...
Hello,
I am looking to get started with NRF52. I am very familiar with TI BLE so not a beginner.
I am looking for a high level introduction to the nordic soft devices...
Hello,
i am new to BLE,
I am using the iot S1xx Softdevice on the nrf51 Dk in order to test ipv6 connection, and now i want to add advertising with the Eddystone protocol...
Sorry I am new to this. Therefore this question may seem to be odd:
I want to build a temp monitor using an nRF8001 (BLE Board Adafruit) and send this data to my mobile...
This is the code I am using to wakeup my system from OFF. It is not working. Kindly Help.
#define Pin_0 0
static void gpio_init(void)
{
ret_code_t err_code;
...
I am creating a system (nRF52 SDK11.0.0 s132) that will get a data ready interrupt on a GPIO (configured via GPIOTE with a handler) from a sensor every 4ms. The sensor has...
Hello,
I am writing an iOS code using Swift3 to connect an iOS10 device to nRF52 pca10040 and blink an LED. The nRFConnect on iOS can easily connect using the device name...
We've currently only been developing our application in C. We now have a couple of C++ libraries we'd like to use and are having trouble compiling the mixture of C and C+...
On a custom board using the nRF51822, with SDK 11.0.0, SD s130 and gcc, I'm seeing the following stack trace when doing some TWI operations to program an accelerometer:
...
