Hi, I'm testing the beacon example
(ble_app_beacon, Beacon Transmitter Sample Application ) with my custom board.
I use IAR 7.1 for ARM, Softdevice S110 ver 7.1, and...
Hi,
I'm trying out S130 SoftDevice. I have 1 device with S110v7 which acts as a peripheral.
2nd device contains S130 0.9 (I've based my code on S120 multilink central example...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Hey I am working on nordic nrf51822 chip ( http://i.imgur.com/q8EM4uq.jpg ).
I want to run a bluenet code which i have forked from github.com/.../bluenet to github.com/....
Hi, I use the nrf 8001C + stm8s. I successfully installed settings nrfGo, but when I try to execute a command OpenAdvPipe I get an error ACI_STATUS_ERROR_CMD_UNKNOWN .
The...
I am using PCA10031 dongle with SDK 7.2. I tried the blinky example in peripheral directory. Unfortunately it didn't work for me.
When I use the makefile from blank/armgcc...
I've tried compiling and running the ble_app_hrs_rtx demo example suing the makefiles and GCC 'as is'. However, the program just hangs and doesn't do anything. Specifically...
Hi,
We have built a BLE product using nordic nrf51422. When system power off mode is enabled, the current consumption is coming to be around 16 uA. In our application,...
Dear Nordic Team,
Thanks for support.
I want to know the possible for voice file transfer to over BLE. I am using BR281 audio detection on semiconductor. I want do the...
I'd like to retain a few bytes after a restart from system_off. I know the GPIO state is retained, are there any other registers other than that? It looks like RTC1->CC[0...
I've been struggling for some time to get L2CAP transfer between an NRF51822 and a Linux machine using bluez.
I've successfully created a connection between the central...
Hi,
I want to understand ANT and want to begin development with ANT once I figured out how it works. After reading posts on this forum I found out that not all Softdevice...
Is there an example for using a 10 pin 2 digit 7 segment display similar the picture below?
It is common anode and actually has 10 pins (pin 2 is the DP or decimal point...
Hi,
I was wondering about that I did not found any information about dedicated pin usage.
I am using I2C/SPI and UART and did I understand it correctly that i can use...
My application has two firmwares with different offset addresses. One firmware sitting at 0x16000 and second one is at 0x25000. I want jump to the second application from...
I have an issue where after transmitting a radio package, is setting up the radio as receiver, get indication for reception (have indications for ADRESS and PAYLOAD events...
I programmed my beacons with ble_app_beacon (nordic firmware). android can locate my beacons without any problems.
I installed nrf connect app, it can find them too.
but...
Hello,
I'm using BLE, RTC and app_timer to blink a led.
I blink the led 10 times when I receive an order from BT (by means of NUS), and then by means of RTC.
uint32_t...
Hi. I'm very new to this so I hope you'll forgive me for my basic questions!
I would like to take data from multiple ANT fitness devices and send it to an iPhone application...
Hi,
I'm designing a 2 layer flex PCB with the nRF51822-CFAC WLCSP package and recommended ST BAL-NRF02D3 balun and i have chosen mono-pole antenna is a good choice,because...
