I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello I tried to do a application update with my own key and it does work.
But then I tried to create zip with all 3 parts: APP+BL+SD (application+BootLoader+SoftDevice...
Hi
With the introduction of softdevice v2.0.1, the connection bandwidth has become configurable to be low, medium, or high; and can be specified independently for TX And...
Hi,
Now I'm using nRF52 SDK v12 and S132, I have some data(about 300 bytes)need to write to the flash. I have seen the fstorage but I donn't know how to use it. Could anyone...
Hi,
I am trying to implement a biometric group telemetry system for my gym and experimentation.
In the past I used a nRF24AP2 module and an ARDUINO PRO MINI 3.3V 8MHz...
Hii,
I want to assign name to my custom service. how can i add it i am using nrf52 chip and s132 softdevice.
I have add new service using sd_ble_gatts_service_add() A...
In my project I need to be able to get time from a continuously running RTC. The softdevice uses RTC0, and app_timer uses RTC1 (and starts and stops it).
(annoyingly I...
Hi ,
I am working on one application in which i am using UART service. Whenever i am connecting to device using nrf connect or master control pannel app, UART service empty...
Hello.
I use the BLE multilink central example to connect to 2 sensors. I changed the example in that way that i successfully connect and read data from a Wahoo Cadence...
the application is examples\peripheral\csense , cap sensor can sense my touch, but when I cover a 1mm acrylic on the cap sensor, will not sense my touch.
so I want to know...
Hi ,
We are using BLE nano board as a connectivity board and mDot board as application chip which is running on mbed platform.Connection deatsils are same as described here...
Hi,
I am working in one application in which I need SAADC to sample two channels at 1ksps and 500 samples per seconds.
I am sending 1 and 2 to switch the sampling rate...
After trying to run keil project after setting conditional breakpoit it raises error.
is it right that nrf52 doesn't support conditional breakpoits? or something wrong...
Hi,
I'm using the SDK11 and SD130 on a custom board which has a nrf51822.
I connected via SPI to a DSP that sends and receive audio.
My handler of the SPI is as it follows...
I'm trying to send a set of 246 bytes by uart fifo. I have a PC side which retreive the data, but I always miss some bytes (4 to 6).
I'm checking app_uart_put return and...
Hello,
I would like to use the nrf51822xxaa as BLE gateway for an ARM application processor (connected through the UART).
I successfully cross-compiled pc-ble-driver...
