When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi,
Would I be able to get more information on the statement below from the nrf52832 datasheet?
"A step increase in supply voltage of 300 mV or more, with rise time of...
As an example, let's see this function from app_hrm (heart rate monitor):
static void conn_params_init(void)
{
uint32_t err_code;
ble_conn_params_init_t cp_init;
...
I am laying out a board in altium using the nRF51422 - just cutting out the essential pieces in the silk box from the nRF51 DK altium project.
I have some concerns. Once...
Hello, I am going to make a PCB to mount the module and programming pins SWCLK/SWDIO/VCC/GND. I wanted to run my module at 1.8v, but I am worried if the nRF51 dev board, when...
[87] CPU: Unexpected wake from System ON Idle when using FPU
This anomaly applies to IC Rev. Rev 1, build codes QFAA-B00, QFAB-B00, CIAA-B00.
I have the PCA10040....
I made a custom board with the nRF52+SDK11.0.0+s132. The firmware is based on the ble_hrs example (modified to fit my board and modified the application, but the basic premise...
I want to change Variable state( 0->1 or 1->0) when I push the button.
I was searching for example relating to the GPIO.
but I did not find that i want.
Everything...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
Hi,
I am working on an Eddystone application for broadcasting advertisement URL to both Android and iPhone devices using the nRF52DK with the latest SDK 12.2. I have read...
Hello,
our company wants to launch a new device using Bluetooth.
We use your chip and your Softdevice S110 v8.0.0, what Bluetooth licences are we required to pay, and...
Hi,
I am using SEGGER Embedded Studio 3.10h on OS X and SDK 12.1.0. I get this error
main.c:614: undefined reference to `ble_dis_init'
even though I have:
...
Hello,
We have found a bug in nrf_bootloader that can prevent the application from starting up properly.
In nrf_bootloader_app_start.c, the nrf_bootloader_app_start()...
I saw the example of Andriod nRF Master Control/Connect app triggering the FOTA for mbed platform without using any button. Unfortunately, I don't have Andriod device and...
during the pcb design of nrf52, is it compulsory to totally copy your reference pcb layout . since our case need to design a small size device, so i have to modify the pcb...
Hi,
I wanted to know whether Bluetooth 5.0 will ever be supported on the NRF51 series chips or we need to migrate from NRF51 to NRF52 in order to have Bluetooth 5.0 in...
