I was doing some developement for a custom board on NCS v2.9.1 when i noticed some of the changes i was making in my prj.conf weren't being set in the application. My impression...
In my circuit I have a MOSFET which disconnects the battery. There is a GPIO pin which turns this device on and I'm using regulator-fixed to drive it during start-up. A short...
We are currently using ncs 2.9.0 on an nRF5340. We use the BT_HCI_OP_VS_READ_VERSION_INFO to determine at runtime what version of the BLE stack is present. This information...
Hi I'm trying to load a custom board with nrf9160 with the Serial LTE Modem, and route the AT commands to the UART from a coprocessor (ESP32C3) I have followed the guide on...
Hello,
we have a working system on the nrf9161 that works without zephyr. We have our own secure firmware that successfully uses the cc310 after we start the actual application...
Keep hitting my head on this inconvenient workflow.
Edit build config
Select target custom board
Build config
All OK
Edit config again
Target board has been...
I have used the Programmer previously with success. I am attempting to program the Dongle (10059) with a slightly modified version of ble_nusc_usb_dongle. Although it claims...
Hello,
Is there any information on current consumption for the nRF51822 when running the micro-esb examples? I'm curious as to how much current is being used in a situation...
I'm testing a custom board I did. The board has this 16Mh crystal
geyer-electronic.de/.../GEYER-KX-7_01.pdf
The CL of the crystal is 12 pF. I'm using a pair of capacitors...
Hi,
I am trying to get the ble uart example from the sdk 0.9.2 working on my nrf52 DK board.
But the nRF UART v2.0 application on my android phone, quits instantly after...
Hello,
I'm looking to send a 32 bits word to the example "LebButtonDemo", using an iPhone application created with Evothingd Studio (it uses Javascript).
I'm able to...
Hello
at the moment I have a running S120 BLE firmware update on my nRF51822 hardware.
This works fine on my desk.
But we have the additional requirement to update the...
Hi
I have an custom board which uses an nrf51422 SOC. I am facing issues with my radio.I use an softdevice s110 with an application on it.
The code just works fine with...
Hi Noedic,
I triggered the DFU function through APP, the device restarted and the base service UUID changed from 0x0001(nus function) to 0x1530(dfu function), but it is...
Hello,
I am working on S120 SD v2.1.0 for central and S110 v8.0 SD for peripheral and SDK9.0 and I am able to configure 1 single uuid on central and connect to multiple peripherals...
Hi.
I would like to konw some ditails aboute nRF9E5 device:
What is the rang between 2 devices using 433 mhz.
do you have any samples codes ? i need to trasmitt...
Hello,
After i disable SD i try to count ticks on TIMER1 from RTC1 via PPI.
Timer1 is configured property but TASK_COUNT don't increment cc.
I see that event TICK on...
So. After countless hours of messing around, reading SDK, examples and stuff I'm begginning to feel kind of frustrated. I want a microsecond timer. For that I tried a number...
Hello,
I use nrf51422 for my project. I have to collect data via BLE nus from phone, but after that i don't need SD anymore. Can i use blocked hardware, like RTC0, after...
hello there i am trying to interface adxl345 with nrf51822. my code is like
#define ADXL345_ADDR 0x53U
#define ADXL345_ADDR_WR 0xA6U
#define ADXL345_ADDR_RD 0xA7U
#define...
I am trying to modify s130 experimental app example so that my board could connect to any peripheral and discover all of its services. As peripheral I use "ble_app_multilink...
