Hi everyone, I'm working on a project with Zephyr (v2.9.1) and I'm facing a compilation issue related to managing two SPI devices on different buses ( spi0 and spi2 ).
In...
Hello, I'm running an example of channel sounding using nRF54L15.
The build is fine, but the following error occurs during flash.
Python is using 3.12.4 version. As you...
Hello, I am trying to update the modem firmware to v1.3.7 using UART using the nRF modem bootloader API. For context, I am running nrf-sdk 2.9.1 and also using the SLM application...
Hello,
I'm here again because this time I need to autoconfigure (configuring from inside program, no use of any nrf app) heartbeat destination node and source node.
For...
We have developed an application which uses the nRF9160 together with the same GPS and Ethertronics/Kyocera/AVX antennas as that of the nRF9160-DK . For the LTE antenna, we...
We're trying to measure supply current used by the NRF9151 DK but have discovered that the current measurment connector (P22) only includes current supplied to VDD, and that...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
I followed the instructions from here developer.nordicsemi.com/.../a00081.html
to make my application support DFU OTA. Despite of some errors in the instructions I managed...
Now I am using hid mouse example to develop a project which requiring bond process. Everything is OK but the question: I need report the btn number which trigger the system...
I copied the example "ble_app_hrs_s110_pac10028(nRF51 PCA10028)"in the nRF51 sdk 10.0.0. I Changed the configuration to make it run on BOARD_PCA10001. But the program keep...
Hi,
I need to update the Min and Max connection parameters run time.
Is it possible to do so?
Also can i update the Min and Max connection parameters through an iOS app...
Hi,
I am using app_pwm in low power application on nRF51822 with soft device S110. Today I measured power consumption and found the current was ~1.5mA during advertising...
Hello,
There are two problems on nRF52 ble uart example code.
I would like to know is there any misunderstanding or mistake I made?
or anyone met the problem too.
1...
Hi All,
I am starting the process of getting our product Bluetooth RF PHY tested, and our lab has asked an interesting question.
What is the image frequency of the nRF51822...
Note: I am using v8.0.0 of the s110 softdevice on the nrf51822.
I am developing an application with the nrf51822 that uses pstorage, bluetooth, and SPI reads/writes.
...
I was looking at the nrf52 startup code and noticed something.
The handlers for UsageFault, MemoryManagement and BusFault are there.
But they are not available in the vector...
Hello,
are there some known reasons why S120 can reset the system while BLE connection to S110 peer is lost? I have S120 and two S110 connected. When i take one of S110's...
Hi, I'm trying to work out, why p08 stops working as DO if mbed Serial is used.
Code is pretty minimalistic:
#include "mbed.h"
int main() {
//Serial pc(p15, p16...
Can someone please provide detail on the clock source for the SysTick in the nRF52? Is it clocked by the processor clock or an additional clock source? I'm trying to understand...
what's the difference between app_timer api an nrf_drv_timer
are they using separate timers or the same timers?
if they are using the same timers, can app_timer_create...
I'm trying to use app_timer without softdevice, I tried to initialise it explicitally but still not working
static void lfclk_config(void)
{
uint32_t err_code = nrf_drv_clock_init...
