1. I am trying to implement DFU(with USB&BLE) and USB Mass Storage with FAT FS filesystems on external QSPI flash. I am getting the following build errors- with SDK version...
SDK: nRF Connect SDK v3.0.2
DK: nRF54L15-DK
Sample: spi_flash
default:
mspi-max-frequency = < DT_FREQ_M ( 8 )>;
If I change it to 32, it will printf these...
Dear Nordic
I am programming with nrf52833,ncs v2.9.0 base on sample\peripheral_hid_keyboards
Peripheral side(nrf 52833) adverting as Scanner_CE42,and iphone connect to...
I have read info somewhere which said there is method to crack the protection just by setting UICR APPPROTECT register.
I want to know if Nordic has upgraded the protection...
Hello,
I'm looking for answers and some explanation for two main questions - is it possible to perform non-simultaneous multi-image FOTA over WiFi? Is it possible to support...
Hello,
We are developing nRF5340 SoC and is currently using Thingy53 as our reference design, our NCS version is v3.0.2.
So far, we've been able to use dfu-util tool to...
Hi,
Due to pcb constrain, we need to use single button mode with PG/RESET routed to SHPHLD. In this mode long press for reset in the datasheet but nothing is said about...
Hi
I'm trying to run the HRM_RX exemple on the nordic NRF51422. This is my configuration:
-Eclipse IDE
-ARM GCC 4.8.3
-NRF51422_AAC0 so I'm using the lasest SDK 4...
hello,
i am trying to use the example for the ble_lbs from github.
I get no erros on compile and flashing.
But wenn i try to see the device in the master control panel...
I've been slowly and incrementally adding changes to the ble_app_multilink_central example from nRF51-SDK-6.0.0. This is an exercise to understand where my other app stopped...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Hello everyone!
Firs of all consider I'm very new in micro controllers programming/debugging, so your patience would be much appreciated.
I have a nRF51822 mKit like...
I use multilink_central example and try get information about discivered service:
APPL_LOG("[CLIENT_LOG]: Count of services: %d\r\n", p_client->srv_db.srv_count);
APPL_LOG...
my led connect whit a pin like this:
the led positive connect whit VCC and the negative connect whit a pin through a resistors.
when I config the pin as a output like...
using the nrfGoStudio to program s110_nrf51822_6.0.0_softdevice.hex
Tools:
Jlink,SWD mode as the figure:
but there are some problem
1:we can download demo BlinkLed...
Hi,
I need a RTC calendar ble stack on nrf51822 .
(turn on the RTC0 on ble stack and get the count, how to setting the rtc wakeup )
which calendar need follow :
track...
Hi,
I'm trying to get a time stamp using that kit, but I'm having problems doing it because always I upload the code to the kit, it stops working.
I add here the code...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
The bluetooth device keeps getting disconnected from the app, even when its not 'idle'.
I am using the android app mentioned here .
I need help getting started to solve...
I would like to use nRF51822-based BLE module as Master role or Slave role.
How do I give role(Master or Slave) to nRF51822-based BLE module ?
What should I use ?
I ask...
