Hi,
We need to write binary content from a binary file (.hex or .bin) to a specific area of the external flash (QSPI).
According to this topic: , this is similar to our...
Using nrf sample from v2.9.1/nrf/samples/crpyto/rng Configure build with v2.9.1 SDK/Toolchain Configure build with board target: nrf5340dk/nrf5340/cpuapp Add MCUBOOT support...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
Hello,
I am currently using nordic connect sdk version v3.0.2 which seems to be the latest release on github. I am using https client example. As per the requirements...
Hi, nordic team
There is an issuse happened in my custom board with nrf52833,programming in ncs v2.9.0.
peripheral side is programmed base on peripheral_hid_keyboard and...
Hi all,
We are currently developing a modem application for use with a Linux host, based on a nRF9161 using nRF SDK 3.0.0 and toolcahin 3.0.1
When compiling the Serial...
Hi,
I'm using nRF SDK 16 for my application on the nRF52840 custome board. When I set both parameters (i.e., support for coded PHY and 1M PHY ) in the scan initialization...
Hello,
I am doing a search in the Eclipse to find texts, I noticed that Eclipse is not finding any of the texts from the Include files. I did a google search on this issue...
Hi,
I use pstorage to allocate 32bytes of memory with 2 block, means each block having 16 bytes, when I write 16byte data into block_0 portion, I am not able to go to the...
Hello,
I use the Segger J-link software with my PCA10001 and recently updated it to last version (v.5.1). After install it asked me to update the firmware to the last version...
Hello,
I'm trying to flash external nrf51422 module.
I want to flash both softdevice and application. I used below commands:
mergehex -m %SOFTDEVICE_NAME% %APP_NAME...
I want as much control over advertising as possible. Barring that, I want to understand why the softdevice automatically goes back into advertising after a GAP disconnect...
Hi,
Assume that we want to send a data array by putting it in consecutive advertisement packets. I know that data update has to be done by calling ble_advdata_set(...)...
Hi
I'm trying to implement battery level on my custom profile.
So I used battery.c and ble_bas.c files for the battery service from nodic's sdk nrf51822_v4.4.1.31827....
I have make over your bootloader example to create my own without BLE support in bootloader (new programs are send in application instead of in dfu bootloader). Bootloader...
Having some trouble using the NRF52 as RX and nrf24l01+ as TX. The NRF52 receives the packet, but for some reason it always says CRCerror.
Anyone ever tried to use NRF52...
Hey Guys,
In my custom board I need to use two different I2C bus and one SPI.
At the moment i'm using twi_master to comunicate with one of the TWI bus,
but to switch...
I have several nRF6930 beacon kits. Some have a sticker indicating they have a PCA10006 board, on others, the sticker indicates PCA20006. All PCBs are marked 400059 0138RUBR...
Dear developers,
As we know, nrf51 has a maximum flash erase / write cycles of 20.000 times. So, in my code, I have implemented a counter that checks if max. flash write...
Dear All,
Does it worth coding a selection (scanning?) of "relatively free" radio channel to stick to?
Say, before starting our distributed application (consider a network...
