Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice , like this:
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
I have a nRF51822 device.
When the connection interval is 50ms.
The transmission distance can up to 50m+.
But, when the connection interval is 1000ms.
The transmission...
The ble-sdk-arduino UART examples (and others?) have a rather convoluted scheme to delay the ChangeTimingRequest until after an ACI_EVT_PIPE_STATUS event indicates that the...
Hey guys,
With the BLE stack initialized, I’m not able to get the power down to where I’d expect with nRF51822, running SD S110 8.0 and SDK 9-2.
I’ve tried three, very...
Hi,
I'm new with a) the Nordic Softdevice environment and b) using the nRF52. So there are a few questions...
As a starting point I've used the template project (.....
Hello everyone ,
i am trying to increase the sound of the buzzer so can anyone suggest me do i ahve to increase the supply voltage or do i have to modify the dutycycle...
I have now used days trying to create a working clone of "dfu_dual_bank_ble_s110_pca100028" so that the source would compile and result would work correctly, independently...
I have 5 LEDs - ideally I would like to control the brightness of each one independently (i.e. 5 PWM channels). I'm using SDK 9.0 and SD 310. I have been looking at the PWM...
Hi,
I got the ble_app_beacon_s110_pca10028 from Keil_v5 Pack Installer to compile. I followed the step to use nrfutil.exe to generate a zip file. But when I did the DFU...
I can't afford nRFgo Starter kit as of now; so my question is if there any other way to program my application (firmware) in nRF8001? I am looking from following options:...
Hi,
File "nrf_drv_config.h" defines both TIMER1_CONFIG_BIT_WIDTH and TIMER2_CONFIG_BIT_WIDTH as "TIMER_BITMODE_BITMODE_16Bit", can these timers be configured as 24 bit...
HI,ALL,
I want to take use of hardware flow control, but when i set or clear the RTS signal, it failed.
something about the attempt as following:
the purpose:enable the...
Dear all,
I'm using an nrf51822 (running softdevice 6.0.0) with the proximity profile.
With iOS8, I was able to find & pair my device with the nRFproximity app.
After...
Hello from Spain!
It is my first time that I use a Bluetooth chip so I am following all your code stack and some answers of this portal, but I am having problems with the...
Hello everybody,
I am using RTC1 for time measurement, this works fine as long as no BLE communication is running.
The RTC is initialized with
const nrf_drv_rtc_t...
situation:
We are developing an nRF51 application with OTA DFU. we use SDK 9.0.0 and the DFU bootloader version is v8. We have prepared different two packages. Single OTA...