Hi Team,
To implement iBeacon what are the things to be take care at the peripheral side.
Whether the code for advertising the peripheral in "CoreBluetooth" and "CoreLocation...
Hi, I have both the nRF8001 dev kit and the nRF51822 Eval Kit (EK). We are using the nRF8001 for most of our project with the BLE Arduino SDK. But I wanted to just load a...
Hi,
What is the suggested method to change a pending request, and make it earlier than previously requested, without closing and reopening the session?
For example,...
Hi,
I am using a custom pcb with a nRF51422 chip, and trying to setup ANT communication between 2 modules, but the sd_ant_channel_id_set call returns an invalid address...
Hi,
To use bidirectional continuous scanning mode in ANT, I have to transmit Extended Broadcast/Acknowledged/Burst messages using ANT Msgs 0x5D, 0x5E, and 0x5F (ANT Message...
We are preparing to get BT qualification for our product, developed with the 6 stack now, however want to update to 7 when it is finally released. A comment from the testing...
What is the best way to minimize transfer in progress errors when trying to send ANT messages? I am using the S310 stack on an nRF51422. I have a busy ANT channel that is...
Hi,
I am developing some DFU OTA firmware for nRF51822, QFAAH0 (v3 silicon, 256kB ROM, 16kB flash), on a custom board, using SD110v8. Both my application and bootloader...
I am playing with the nRF52-DK preview and I noticed the samples in the 0.9 SDK are set to 32k of RAM. I increased it to 64k as per the chip specification and had no problems...
Hi,
I'm in a situation where I need to get two devices communicating using S110. I am aware that I can send using S110 and I am only referring to small transfer sizes....
Hi,
I meet a very strange situation when I tried to wake up nRF8001 from sleep.
I send 0x05 to nRF8001, it replies me ACI command 0x40 is unkown (0x82).
I have checked...
Greetings,
I recently bought an nRF51 dk and was trying to see how to implement the AVRCP profile to play/pause music on a smartphone.
After some research, am i correct...
I measured the conducted power on the PCA10028 demo board and get ~2dBm out when I set the output power to +4dBm. It appears the PCA10028 is using a discrete balun. Is 2dB...
Hello,
Setup:
SDK 9.0
SD 8.0.0
I have an application where we are using Pstorage to store persistent system settings.
When I flashed the device we were using this...
Dear All,
I'm a beginner in programming of Nordic component.
I try to synchronise the date and the time between client which is an application in PC and a component...
I'm currently developing a concurrent central/peripheral application using the nRF51, S130 and SDK 9.0.0. It uses the Nordic UART Service, and it would be nice to make use...
Hello,
Is it possible to use EasyDMA directly with nRF52 SDK without using one of the higher level libraries that use it, i.e SPI / UART? I am interested in implementing...
Hi:
I want to let link manager controllby by me. for example, I want to ask link manager to emit such LMP_test_control, LMP_activate command via HCI. how to do by nRF51?...
Hi:
for nRF51
I want to send command to link manager by HCI command ,or example LMP_test_control, LMP_Activate , etc. Could I modify firmware to do it ?
thanks;
All...
Hello,
I have an issue that I can't seem to sort out involving the PWM module. I am currently using SDK9.0 and SoftDevice S110 V8.0 and I am using the stock PWM files from...
I have a nRF51DK. And I would like to be able, to enable/disable the softdevice with 2 buttons.
Button 1 on nRF51DK --> Enable Softdevice
Button 2 on nRF51DK --> Disable...
