Hi,
Will PAN item #56 TWI: TWI module lock-up be fixed in the Rev 3 version of the nRF51822/51422?
Also would you happen to have a time frame as to when the Rev 3 will...
Close Bluetooth in Iphone's settings when IOS/51822 is paired and connected normally.
several seconds later, Open Bluetooth in the settings again, and observe the settings...
Hi,
I am trying to power off and/or disable a RR[0] with no success.
I am Powering OFF the watchdog in main and then successfully POWERing ON in wdt_init but then I...
Is it possible when using the S110 softdevice to limit the maximum number of packets per connection event? I would like to reduce the maximum amount of time the CPU spends...
I am using nRF51422 Evaluation Kit with the latest silicon revision which comes with programmable softdevice. The kit also contains an ANT USB-m dongle. I have followed the...
I tried to do send & receive binary data from bluetooth in ios app.
But i only can send & receive string or ASCII code data in my app, do you have any method or idea can...
Hi,
I tried ble_app_hids_mouse with Android 4.4.2, it can work properly for first time connection. However, it cannot be re-connected after switching Phone's Bluetooth...
Hello,
I am working on SDK 9.0 and softdevice 8.0 and the requirement for my application is the device has to advertise till it gets connected and even after disconnection...
Dear all,
I get a new nRF51-DK and I am trying to download an hex file into it.
I downloaded and installed nRFgo studio.
I connected my nRF51-DK to my...
Hi. I've gone through a lot of documentation and can't seem to find if this is documented by Nordic semi.. please answer if you know, or can point me to experiments/documentations...
I soldered 5 pieces of PCBA with nRF51822, but I got only one PCBA which can connect to J-LINK. I checked the bad four and found that SWDIO of nRF51822 on the four board is...
I'm having a weird hardfault and, I can't make sense of it.
Here's what I do know:
nrf sdk 9.0.0;
nrf51422 on a dk;
I have RTC1, SPI0, and TWI1 enabled (also a uart for...
Hello,
call of app_pwm_init() function forces logic 1 on PWM enabled pin after advertising timeout expires. Why? It causes my LED to turn completely on after advertising...
Hello,
In my code I would like to switch between BLE advertising and listening nearby devices (and save their RSSI) in the same code. After each advertising period, I would...
i have use nrf51822 and android app(nRFuart)
i was masure currunt through DSO but i think its not accurate...
i can't masure exect(high accurate) currunt consumption in...
I read through the following post and still couldn't get debug info out.
I have tried the settings there and from another post with no luck. I'm using putty on a win 8...
Hello everyone,
I am trying to enable notification on a characteristic based on the code example from nAN36.
Unfortunately the sd_ble_gatts_hvx() function returns:
...
I know that suggested debugger for nRF51xxx is J-Link or openOCD with CMSIS-DAP, but I would like to use BDI3000 debugger, which does support SWD interface and Cortex-M0 processors...
Hello,
I desperatly try to implement a bootloader with the s310 softdevice. When I received the data to be written (via BLE), I erase the flash:
std::uint32_t rc = NRF_ERROR_BUSY;...
Hi,
When will the user guide be available? I have the PCA10040 V0.9.0 2015.39 PCBA that I got from the Global Tour. I am using the nRF51 Development Kit User Guide v1.0...
I try to build example projects in 32k limit Keil uVision. I'm not able to build some of the projects (e.g. Heart Rate Service) because of the 32k limit for the compiler....
Hi Nordic developers,
I'm using TWI software driver provided by NORDIC.
I need to have 400 kbps frequancy.
I have seted TWI_DELAY() to 0 and TWI_MASTER_TIMEOUT_COUNTER_LOAD_VALUE...
