Hello, I am tryong to use to masters to communicate with two accelerometers.
Q1_ I found the following image from Nordic's website that shows SPI0 pins but there is no indication...
In the nrf51 series reference manual section 12.1.9 it states that there is hardware protection that prevents write instructions from being executed and that there is more...
Hello, I have established the connection between two pca10001 boards, one as central and one as peripheral using multilink_central and multilink_peripheral. I have serial...
Hi,my friend,
Now,I use nrf905.Situation is as follows:
I use the NRF PCB circuit of data manual.Nrf905 work, often loss of data.
1.The Product host is to use the stick...
Hi,
I want to use the Blend Micro with more security. I want use a passkey for the Bluetooth connection. For example through the iOS Device.
Is it possible? Static passkey...
How do I receive multiple signals simultaneously at a single receiver (433MHz) with multiple transmitters ?
I am working on a polling system. This one is similar to the audience...
Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
Hey guys,
Trying to use TWI in the lowest power way possible, non-blocking. Is this the right way to do it? When I run this, I get the callback event handler to execute...
Hello,
I'm looking to disable the Bluetooth in the ledButtonDemo,.
In the led_write_handler, I've replaced the code by :
if(led_state == 0)
{
sd_ble_gap_disconnect...
Hi
I tried to check nRF51 SDK on IAR Embedded Workbench for ARM 6.70.2.6310. But he said that the project is broken.
It looks like there are no setting files for all...
hi,
i'm working on change 'example project file using softdevice s110' to 'using s130'.
but, i don't know where exactly need to change.
just downloading softdevice s130...
I need to use the 8.0.0 version of S110 with my beacon which contains 7.1.
Since the Android DFU utility supports updating the Bootloader and softdevice with a zip distribution...
hi,guys
For testing the comunication between BLE+timeslot device and radio device, I change the code as below:
void start_timer(void)
{
NRF_TIMER0->TASKS_STOP = 1;...
Dear Nordic,
Whats wrong with the below code. It works well in RFduino but when I try to port the same code in Keil environment.Its not working throwing error as
1.identifier...
I just got a new target board back from fab/assembly and I'm trying to use the debug out connector on the PCA10028 to program the new target.
My target is the NRF51822...
Is there a beginners guide on how to get a console output working for the following setup?
keil v5 & SDK 6.1
nrf51-dk connected with the
TC2030-MCP-NL to a
nrf51822...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
Hello,
I am new to working with nrf52 and was looking for a way to make printf work in a blank project that I have created. I followed the uart example for the peripheral...
Hi
Now I'm using the pstorage module to save some data.But I meet some problem,I hope I can get your help,thanks a lot.
It seems that the block has been created successfully...
Hello everyone
i am trying to run the pwm library exmaple from github into the SDK VERSION 9.0 but it is showing lot of errors like
............\components\drivers_nrf...
Hello,
I am working on S110 SDK 9.0 and softdevice 8.0 on EK board. I am able to authenticate the connection using static passkey.
I need the information about encrypting...
