I am trying to create a partition on my external flash using littlefs
Here is the line that is returning me an error
FS_LITTLEFS_DECLARE_DEFAULT_CONFIG ( storage ...
We are developing HW that includes nRF9151 running DECT NR+ with the Wirepas stack for mesh connectivity between multiple units. The product is expected to move between geographies...
Hello Nordic Support team,
I'm receiving the Transmission failure and Lora Initialisation failed message despite to correct wiring and everything else. I'd attach a link...
I am reaching out to seek your guidance on a development project involving the nRF52840 and Semtech SX1262 LoRa transceiver.
We are building a marine crew monitoring and...
Hi，
Platform : nrf52840, NCS 2.7.0
I would like to get the MCUBoot image swapping progress without modify the NCS, and display a progress bar on the LCD to indicate the...
I enable cs procedure and set the procdure count equals to 3, let procedure interval to be 10.
I want to change the cs channel map between procedures. so when I send HCI_LE_CS_Set_Channel_Classification...
HI ALL,
I want to obtain the status of the upgrade process using mcuboot ble, such as flashing lights when starting the upgrade, flashing lights during the upgrade, and...
Hi,
I'm new to nordic's product and new to study open mesh framework. But I have two questions:
Q1: what access address mean? Is it a parameter of mesh network ?does different...
Hey everyone, I'm trying to compile blinky example, using ARM on Mac OS X. I use st-link 2 to flash it. So, the first when I do 'make' command I've got errors
Makefile...
Gentlemen,
I apologize if this is not the correct place to post this question.
I have a potential project to start a BLE project but their requirement would be start...
I'm developing a new board with nRF8001, after reset i correctly get the DeviceStartedEvent 0x03 0x081 0x02 0x00, after that i go into setup mode sending the configuration...
Hi,
I am using nRF5_SDK_11.0.0_89a8197 at center to debug ble_app_uart_c project.
The center can connect the device well at the beginning. But if I power on and power off...
according to the introduction of mesh framework( value storage part), it says all mesh data is saved in a structure. My understanding is : Handle means a trickle instance...
How to configure S130 Softdevice as Completely Central(S120) i.e with Out Switching its mode to peripheral to operate like a central.
Is there any API or Example to do...
For example, if the first page is erased then it will set this page as swap page and continue looping without increasing the 'page' variable.
This means that the last...
Hi,
I have flashed boot loader to 0x7A000 (Size 24kb) and Softdevice to NRF52 DK ,then flashed application using nRF connect .
Am also able to update application after adding...
Hi,
I need PWM on 2 pins, with a varying duty cycle, and read some posts in this forum on the subject.
I am still using SDK7.2.0, with SD7. Our product is stable, so I...
Hello, a few days ago I was having trouble with RF performance on a custom PCB using the NRF51822. I posted here to get feedback and figure out where the design went wrong...
sdk : v8.1.0
os : ios
tool : nrf tool uart
use the ble_app_uart, it worked normaly. and add duf fuction in the application by the notice
[http://developer.nordicsemi...
Dear all
I found that the frontline BPA sniffer can't catch the connection data between Android5.1 or ISO and BLE device. Does this normal? How can I use the sniffer to...
Hello, I have to implement infrared sending and receiving of a modulated signal in pre-existing code.
I have managed to implement infrared sending thanks to the ble_app_uart_IR...
Hi!
I have creat two timer with app_timer_init.
start the first timer trigger every 4 ms, every 125 times(approximately 0.5 sec) to start the second timer which trigger...
