I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Greetings,
I have a peripheral (S110) , when it is connecting to a central, it also need to scan another broadcaster (beacon) to obtain its RSSI and send to the central...
I have adopted the S120/S110 multilink example to the following: central.zip and peripheral main.c
I want to send a notification from the central to the peripheral and...
I've developed an application on the nRF51 DK, now for further testing purposes I need to upload it to the nRF Beacon (PCA20006).
My software uses SDK8 (S11 v8) and it...
I want to get rid of the board support package, and write my own code to interface with the least complicated drivers for UART, BLE and SPI etc.
If I remove BSP I ifind...
hi i have pca 10001 eval kit .I need to connect it with PIC16L1947 controller via uart.The data transmitted from pic is to be collected by nrf51822 and it should send as advertisement...
I am developing an application from scratch for the pca10001 by copying a lot of code from the heart rate example.
When calling "softdevice_ble_evt_handler_set" I get an...
I am looking over the stack-up for the dev board which I received from an FAE and has designed in a 50mil width PCB antenna. I am using this online calculator here:
emclab...
Hello--
The nRF51-Dongle has these 20 pads which I think correspond to a debug port:
On the schematic, it looks like these feed into JTAG signals:
My question...
Hello,
I just got a nRF51 DK and I'm trying the examples of nRF folder in the Pack distribution (SDK 7.2).
I can compile the Blinky project but its not working if I...
i have the nRF51DK that comes with the Segger j-link programmer. Can i use the programmer on the board to program a custom board i purchased from Nordic preferred vendor?...
Hi all,
I am using gcc for my Nordic project and I wanted to add the bootloader. After some reading and experimenting the bootloader worked. Now I thought of making a release...
Hello all,
i am trying to make working the ble bootloader from SDK 6.1 with SoftDevice 7.0.0 and gcc setup (pure Eclipse gcc project frome here devzone.nordicsemi.com/.....
Hi,
I need to develop a BLE service for file transfer between iphone and my device. I chose BLE because the files are very small in size, and as BLE does not need authentication...
Hello everyone,
I got a task which I try to implement using a NRF51822 iBeacon board.
The Task:
Advertise a Device and provide a mechanism to connect without traditional...
I have been using the MCP along with the provided dongle to access a custom BLE service. I would like to build a custom windows 7 application around the BLE service and move...
