We're looking for a Nordic nRF51822 based low profile/small USB dongle that we can use for our iBeacon software.
It would need to come complete with casing and the ability...
Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
I have TIMER2 running at 500us interval. ANT is working as 100Hz master.
Understood softdevice will affect the timing and cause some latency.
I am guessing it is delaying...
Hi:
I'm implementing an controller for an open source drone Crazyflie ( www.bitcraze.se/.../) . My device is similar to pca10001 board.
Since Crazyflie is acting as peripheral...
Hi all!
I've been unsuccessfully trying to DFU the Smart Beacon Kit with the latest firmware.
Using the nRF51 DK and the TC2030 tag connect cable I was able to program...
I am trying to get a communication between two pieces nRF51822 using the my service. I checked the peripheral with Master Controll Panel app and is working fine. The multilink...
Hi,
I have the (IoT) environment running. The Raspberry Pi (with Miredo tunnel) is connected to the outside world. I can ping6 the ipv6.google.com server from Rasperry...
Hi Team,
I am using nrf-51 DK as sniffer.
I need some guidance regarding how to study or analyze these packets?
I don't know what exactly I should check in each REQ...
Hello,
I am working on nrf51822, My requirement is to upgrade the firmware over the uart with help of DFU.
I have made code for that on controller side and fortunately...
In the release notes of the nRF51 SDK v8.0.0, section "Supported devices" it says that "This SDK is optimized for IC revision 3".
I am using a Laird BL600-SA-04 module...
first,PCA10005 can't load sofeware hex that after s110 7.0.0 hex(include 7.0.0),and gostudio note that the given hex file can not open successfully.
second,the PCA10005...
Howdy, I'm trying to DFU my 51822 beacon v1.1.0 with MCP. MCP is failing the transfer. Steps I have taken are:
-Programmed my beacon with segger from the dk, both the SD...
There are apparently only 3 S120 examples available, and one of them is a peripheral example, which can be done with the S110, so really there are only two examples. This...
Hi,
I tried to run example: ble_app_multilink_central_s120_pca10028 but application goes to HardFault_Handler when it reaches sd_app_evt_wait() (in power_manage() function...
I have an I2C device that has an bidirectional interrupt pin.
This pin is pulled high externally with a weak pullup. When an event occurs on the device it pulls this pin...
