Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
The nRF51822 softdevice is generating the following disconnection event:
11:20:09.363365 : BLE_GAP_EVT_DISCONNECTED c=x05dd
11:20:09.365011 : reason = x002a
11:20:09...
The Health Device Profile is continua compliant. Are BLE health related profiles like Heart rate profile, thermometer profile continua compliant as well? Do these profiles...
Hello, I was wondering what the proper process is to set the measured RSSI values at 1 meter is. RSSI at 1 meter is a part of the iBeacon standard, and is also useful for...
I am PHD student in china and doing research about gait retraining. I am designing wearable sensor that monitoring gait and giving vibration feedback to retrain the gait and...
I've implemented my DFU app on Android(4.3). During the test, I found a strange problem, that the performance of writing image data into swap area is very very slow. My Softdevice...
Hi
I thought: let us quickly migrate to the latest SDK.
But that seems to be harder than anticipated.
I run into a number issues when compiling with the new code:
...
Dear Nordic developers,
I'm trying radio reciever example. I want to stay 7 ms in listening mode, if there is no event turn off the radio. For that I'm using timer interrupt...
When connect to iphone4s, whitelist.irk will be generate,and whitelist.irk_count will be add 1
After that connect to Nexus 7 II bouth irk and addr will be generate,and...
Hello all,
I've had problems for several weeks with RF24 Library (enhanced fork). I use different Arduino and NRF24l01+. I know very well different documentation, and I...
use s130-0.5.0
A1 connect B1 with BLE_GAP_ADV_TYPE_ADV_DIRECT_IND, after this, A1 is slave, B1 is master,A1 can't send any type advertisement
use s130-1.0.0
A1...
Good afternoon,
I have developed a custom board based on nRF51822 device and SD-110-v8. For debugging I have been usign the Ulink2 tool with Keil. Now, I want to implement...
This is not working for me. My goal is to use printf() in my code. I follow the steps outlined in this link
..including calling initialise_monitor_handles(); before calling...
I was able to measure current with the test probes I have. However, I really liked the idea of test probes that were like the ones in the drawing below. I have not seen test...
I am using the PWM library in this repository for a nRF51822. I write the following code to generate a ~ 30% dutycycle 500 kHz PWM output:
#define V_CLK 5
static void...
