Hi,
While testing the device firmware update through the nRFtoolbox android application, i get "device has no required service" error more frequently.
I use latest version...
I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
Hi
I have my code like this .
unsigned char *encryptedData;
unsigned int encryptedDataAfterAppendingLength;
memset(encryptedData, 0, encryptedDataAfterAppendingLength...
Hi, After i flashed the firmware MEFW nRF58122 0.11.0, MCP "start discovery" button is disabled. I flashed the lower version MEFW nRF58122 0.9.0. Same issue.
There is exception...
Dear all,
I have a question on the LFCLK accuracy in the smart beacon kit, which is pca20006.
When I see the specification of LFCLK crystal 32.768kHz, this crystal has...
I'm developing a product using a module with a built-in NRF51822 and I'm experiencing a strange error:
After staying in a connection for a long time (hours to days), the...
Hi, I'm making a product with the nRF51822 chip.
I was looking at the MFi.
As you see in the picture, the condition for not taking the MFi is like this.
At the...
Hi, I've written my own ACI code for an arm cortex M3. So far, everything is working fine. However, I've noticed that if all data credits are used up and a DisconnectedEvent...
I'm using nRF51822 SoC and i want to notify the Androïd(4.3) application with the changes of the Major value due to switching the beacon mode . How to change Major value ...
Hi,
i can say that i'm familiarized with nrf51 devices from some time ago.
Using softdevice 7.1.0 and MCP 3.7.1 i was able to perform a device firmware upgrade using just...
Hey I am working on nordic nRF51822, I have a doubt.
Basically I want to use it as an iBeacon and along the iBeacon payload I also want to send some services.
Is that fundamentally...
Hello,
I tried to get the bootloader dfu example with the S110 8.0 and the latest 8.0.0 SDK running but ran into tons of issues. The packet handling with KEIL is just insane...
Hello everyone!
I'm writing here becouse I'm quite new to the embedded world and I'm experiencing some troubles starting with this platform.. I must say that, since I found...
Hello,
In my application, I'm going to power the custom board with a fixed 5V connection. What is the best practice for powering the nRF51422 IC? I was thinking in using...
Hi.
We need to ring the Buzzer with 4.2kHZ PWM.
However, in the event of 4.2kHZ in nRF51822 PWM is inaccurate about 2us.
Please tell us how to fix it.
※link Very...
I use this step-by-step guide to run nrf51 Iot SDK example on nRF51822.
First I modified app_ipv6_coap_client_pca10028 such that I can run it on nRF51822.
I downloaded...
