Hello,
We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application.
After going through the documentation and few other Q&A on the portal, I was...
Hlo
I have designed a custom board based on nRF5340. Now I am trying to do flashing and RF testing of it through nRF5340 development board but can't even flash it because...
Hi all,
I'm encountering an issue with the TWIM30 interface on the nRF54L15 (pins P0.03 - SDA, and P0.04 - SCL), using vanilla Zephyr v4.2.0-rc1.
The setup involves external...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
We are developing a product that will have a wireless and wired option, based on the NRF52840
The strategy is to release the wired option first, followed by the wireless...
Hello,
I'm trying to build the trusted firmware M for the nrf9151.
I did the following steps:
git clone git.trustedfirmware.org/.../trusted-firmware-m
cd trusted...
Hello,
I would like to use the Radio Test Sample from the newest NRF Connect v3.0.2 (v3.0.2\nrf\samples\peripheral\radio_test). However, when I try to build it with "nrf54l15dk...
Hi,
I would like to use my NRF51DK with SDK11 and SD130 to control my SSD1306 OLED screen over TWI/I2C.
To refresh the OLED screen, we have to send it the whole display...
I recently experimented with the TWI Transaction Manager and found the following:
This function would cause HardFault Error
void _BAD_read_func(app_twi_t* param_p_app_twi...
I build esb_ptx example in sdk12, download in nRF52832 board, but from uart tool, I can not see log.
I have enabled log in sdk_config.h, and in options for target 'xxx' ...
Hi,
I have a DFU issue. Using Visual GDB IDE and gcc tool chain.
I Can get my signed application generated into zip then DFU it into the device which all works.
Once...
Looking at the radio notification code in components\ble_radio_notification, it looks like there isn't an option to use the NRF_RADIO_NOTIFICATION_TYPE_INT_ON_INACTIVE event...
Hello,
I am reading mpu9250 and providing timestamping with events. I want to create timer so that when the timer will be called reading of mpu9250 will begin and when...
Hi there
I have encountered another issue with a repeater that I am working on.
The program follows this basic sequence:
Setup as NRF_GZLL_MODE_HOST
Wait for...
Hi, I am trying to use NRF_CLOCK_LF_SRC_RC as clock source with the following settings:
pca10040.h
#define NRF_CLOCK_LFCLKSRC {.source = NRF_CLOCK_LF_SRC_RC,
.rc_ctiv...
Hi,
Am having application with Freertos in which am creating 4 tasks + ble task using Freertos API's. Application is running as expected without any issues.
But in 4...
Am flashing SD 3.0.0 and secure Boot loader and then updating application (with Freertos) via bootloader .Application boots up no issues.
am facing below issues.
1.Am...
Hello,
I've checked the timing diagrams for the CE and IRQ on the datasheet but I would like to know if anyone has actually tested them with an oscilloscope? If yes could...
I am using SDK 11.0.0 on a nrf52832, with FreeRTOS and SD132 2.0.0. I configure the FreeRTOS port so that it uses RTC1 as SysTick. Depending on some compilation macros, my...
Assuming that all peripherals that require the high frequency clock are disabled / turned off / stopped, how long does the HFINT oscillator run after calling __WFI()?
And...
