Hello,
I know this question is more related to Zephyr than Nordic, but I wanted to try asking here.
I’m using the SMP service to send files to my device on a LittleFS...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
Hi,
We're currently evaluating the cellular capabilities of the nRF91 modem using the nRF9151 DK. We've encountered issues with roaming: when the devkit is taken to another...
Hello, Nordic Team! I am encountering a such problem when using the NRF54L15 on NCS3.0.2 to develop a Matter product. I am trying to use the
SubscribeAttribute
method...
Hello Nordic team,
I've recently upgraded my application from nRF Connect SDK v2.7.0 to v2.8.0 , and the previous BLE Disconnect issue has been resolved — thanks again for...
Hi, I want to set different gap event length for different peripheral on a ble central: 1 link with high throughput and 4 links with low throughput.
The sdk is 17.0.2...
From the datasheet, the On mode with all blocks idle draws 2.6 uA.
In my code for the PCA10001, I immediately set:
void sleep(void)
{
__SEV();
__WFE();
__WFE();...
I was going through online material all of which mention that the profiles and protocols (GAP,GATT,L2CAP) i.e. the host for a BLE implementation is a software stack rather...
Hello - I have gotten blinky_example up and running in eclipse using the SDK 5.2, nan-29, and some additional google-fu.
Now when I press debug and the play button, it...
I am trying to use nRF UART app and nRF8001 chip. But I cannot change the device name. I intend to change the device name after nRF UART app detects the device. Plus when...
I'm trying to create a method so a users can initiate an OTA update from a paired device. To that end I've written something which is supposed to invalidate the data at the...
I'd tried some first steps using nRF Sniffer on a linux host.
Within sniffer_uart_protocol.xlsx I read something about the Uart packet format et cetera.
I'd programmed...
I am trying to get ble_app_beacon exampel working on the PCA10001 on my nrf51822 working. However when I simply run and reach APP_ERROR_CHECK(err_code) inside "advertising_init...
Reading through the nRF51822 Beacon reference design it states that there are Keil ARM project files available. Does this mean that the example code given after purchasing...
Hi all。
I am programming a nRF51822 chip, using the S110-nRF51822_6.0.0 soft device,download ble_app_hrs.hex。
I used app name "nRF Utility".I can connection nRF51822...
Hi,
i have some more, for me fundamental, questions and i hope some one can help me :)
1.) can i use the advertise function whenever i want or only in connection interval...
Hi All,
can any one please share information related to this
1)please explain clearly about channels and pin?
2)can 2 gpio pins hooked to a single gpio channel?...
I'm not sure if this belongs properly here - but I wanted to send out a thank you to Ole Morten.
I saw your reply in http://www.funwithelectronics.com/?id=168 and this...
Are there any plans to create a Google Glass compatible app like the nrf UART app? I'm trying to link a microcontroller with Google Glass via your bluetooth low energy module...
I'm using the Arduino SDK but I don't think that should matter for this comment. I think a small change to some of the lib_aci functions would make it easier to use them....
Hi,
I'm using an arduino uno with a readbearlab shield with v1.1 to send sensor data to a android phone.
Using a timer interrupt I try to send data every 0.1 sec (10hz...
