Hi Nordic team,
This is a follow-up to my previous question here:
Can nRF52833 perform PAwR while also syncing to another PAwR device?
We are now extending our design...
Hi,
I'm trying to build nmea parser, so I have a functionc hecking all nmea sentences and trying to get double value, but I always go bad double value. For example here...
Hi,
With several nrf52840 based prototypes, I had serious problems. I could see them die after flasing them a few times. And this was not just one dying, it was all of them...
Is a common ground required when measuring current in current meter way?
Can externally supplied voltage exceed 5V? Will this cause inaccurate test results?
I'm working with nRF5340 and nRF Connect SDK 2.9.0, using sysbuild and Partition Manager for my project. I want to enable Zephyr's coredump feature and store dumps in internal...
How can I display the nrf serial terminal logs files on VS Code while keeping the same colors and text highlights for dbg , inf , wrn , etc., just like when viewing live logs...
Hello,
How can I put the nRF54L15 into continuous wave mode? And I assume after entering CW that I can freely change channels using the FREQUENCY register (0x708). Is that...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
For conventional Bluetooth, if two devices are connected, we can send and receive text/bytes to and from each other. It is generic since the two devices can be from different...
Hi,
I will just reiterate that question again.
I really need to get 32K RAM beacons, but Digi-key apparently has only 16K RAM or v.1.1.0 modules. Could advise where...
I read this post with great interest!
devzone.nordicsemi.com/.../
I'm having a similar problem with my Nordic Beacon application. I followed the advice to switch my...
I am using a nRF51822 to send data to an iOS device.
Because latency is critical to my application, i 've set up a test program that sends a packet every second , using notifications...
I have some questions about the scan response packet.
Can a scan response be sent with a peripheral that is configured to be connectable? IE not a beacon.
I read...
Dear Nordic Team,
Thanks for support.
I am using nRF5_SDK_11.0.0. How can i initialize the softdevice with internal RC oscillator in my source code. I am using the below...
Hello;
I'm trying to get data over the TX pin to be sent to the RX pin on a Raspberry Pi.
I have it working on several boards: The nrf51822 Development Board, the Redbear...
The radio notification tutorial ( devzone.nordicsemi.com/.../) says:
"The distance is the time window before/after the radio goes active. The radio events are radio_on...
I'm slightly bamboozled by the LFCLKCSRC options in the NRF52 datasheet / product specification.
Bit field SRC makes sense. Set to 0 for the internal RC oscillator, 1 for...
Hi
I am currently using the boot loader from SDK7.2.0, compiled using Keil.
However, for all the other software I am using GCC. But GCC support for the boot loader was...
Hi, i am trying to send my notify characteristic every 100 msec, i am using timer for this and when i am connecting to the nrf app, my nordic device is sending the data but...
Hello,
Thanks for your reading.
I tried to read the CHIP_ID value(0xD1) of BMI160 in MetaWearCPro firmware using SPI.
But I could not get the correct value(0xD1). The read...
Hi, I use the following.
Raspberry Pi 3 (RPi3 with Raspbian Jessie 4.4) as a router,
RPi3 is connected to a Wi-Fi router to access the Internet by using the built...
