Hello Guys
I'm currently working on a BLE AoA (Angle of Arrival) application using the nRF52833 Development Kit . I’ve run into some challenges regarding hardware connectivity...
Hi
I'm migrating applications I wrote using SDK 17 to nrfConnect 3.0 with Zephyr.
I implemented USB devices with combined multiple USB classes. One of those classes was...
Hi,
I am working on ncs 2.9.1 @ nRF54L15.
I followed this academy course to add a single channel saadc in simple mode:
ADC read works properly, but the current read...
Hi,
In one of our future hardware designs, we have a MPU (running LInux) connected to a Bluetooth SOC over a serial interface (uart/spi/...).
Our first approach was...
Hello everyone,
I'm working on an NRF54L15 DK evaluation board and I need to use NFCT pins as normal GPIOs. I found out here that I should define CONFIG_NFCT_PINS_AS_GPIOS...
We are certifying our device at KIWA. they are testing the WLAN adaptivity and the test is failing. Here is the failure description:
" It was a struggle to perform the...
I downloaded the ncs2.6.0 version using Baidu Cloud in the China region, then set the path in Toolchain Manager of NRF Desktop, and Toolchain Manager correctly identified...
Although there are some posts dealing with bond manager issues, I have not been able to find a similar issue. I am using part of the BLE code from nRFready Desktop 2 v1.0...
Hi,
i have some trouble with acting with the nrf 51822 ADCs. My Problem is that i have an Impuls which is 100 uS long and i have to measure it with 2 ADCs. I know that...
Hi,
What will happen when we press the service discovery button in the master control panel? do we get any event like BLE_GAP_EVT_CONNECTED? I couldn't find any detail regarding...
I'm looking for information to start developing BLE slaves with nRF51822, but I can't find any datasheets/SDK. Do I need to buy the Development Kit in order to have that?...
I have an issue with my keyboard working with the windows suface (on windows 8.1). Occasionally, the last character sent is repeated several times instead of one. I do not...
On the nRF51822, I see that by programming the readback protect register, one can prevent reading code regions 0 and 1 from the SWD interface. However, if one had access to...
Hi,
I just watched a webinar from the bluetooth SIG on how to create source code from the nRFgo Studio for the nRF8001. Is the same possible for the nRF51822? To create...
Hi,
We modified the ble_app_hrs code to work with accelerometer peripheral, and we have created some custom characteristics with custom uuid's. Now we need to set the device...
Hello, Everyone:)
Nice to meet you !
Please could you commennt my first question on this community zone.
I've a question for the accuracy of synthesized clodk 32k on...
Hi
i am using NRf51822 custom board. In that i have NOR(spi0) and LED(i2c0).
But switching from spi0 to i2c0 is not possible so that i am not able to switch
off led...
Hello,
I'm using nRF51822 to implement a proprietary radio protocol. My first attempt, in the receiver, was polling the EVENTS_* registers. An example:
NRF_RADIO-...
I was trying to get access to the app_uart library, so I included app_uart.c in the "Source" folder; then added \Include\app_common and \Include\ble\softdevice in order to...
Hi,
We are using nrf51822 custom board.
i want to hard reboot of my device whenever gpio button is pressed for longer than 10 seconds.
i am using ble_app_hrs application...
from the product spec
NOTE: The 3 bit pipe information in the STATUS register is updated during the IRQ pin high to low
transition. The pipe information is unreliable if...
