Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
Hello,
Could someone give me a hint with the following problem?
I am using two example projects (ble_app_uart_c, ble_app_hrs) to connect a central and a peripheral.
An...
I created xml file for heartrate server using bluetooth developer studio and the plugin nRF8001_Arduino (plugin nordic semiconductor for arduino)
the generated xml file...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hi,
I need to implement an application who acts like a GATT client and gets notification from a GATT Server (on smartphone) and then sends the information to a GATT Client...
I am wondering what is the lowest DBM/RSSI i should have to make sure my connection between devices is safe both with setting up a connection and datatransfer?
Hello,
I know it is not recommended to use SD8.0.0 and SDK8 on revision 1 ( QFAAC0 ) based modules.. But as it is for testing purpose only and would save me a lot of time...
When not programed bootloader,my own 51822 module can work without Development Board,i supply the power through the button cell to my module.
But when programed bootloader...
Hi,
I want to use ble_app_multilink_central example for my own application. Here are my problems:
Setting MIN and MAX CONN_INTERVAL to more-less 20ms or lower (both...
Hi.
In my program I need a frequency at 2 MHz (a square wave with duty cycle at 50%), it should just run a frequency in a short time, under one second. Also the code must...
Hi,
I'm using a simple timer with interval set using "APP_TIMER_TICKS(1.4, APP_TIMER_PRESCALER)" alongside softdevice. Now i'm trying to get it to go faster but it would...
I got this error when programming the Development Dongle. The dongle is recognized in the
Master Control Panel as a COM4 - xxxx, and when is connected a green led and blue...
Hello,
We are French students in a school of engineers. We are developing a project based on the nrf51822.
Actually, we implemented RIOT OS on this SoC and we would...
I am currently using softdevice 8.0.0.
I am curious if the nRF51822 will be upgradable to be 4.2 compliant with a new softdevice release in the future? My understanding...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
I am trying to allow 2 peripherals to bond to a central, and would like to be able to use 2 push buttons to delete the bond information for either device. Is it possible to...
Hello, Nordics :)
I am trying to develop ANCS device with SDK 8.1, but I have some problem.
This are my environments.
Board: custom board.
chip: nrf51822AA...
