Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Has anyone experience of successful TICK_DV calibration for nRF9E5? What order of accuracy should be achievable?
In my application I maintain a software RTC clocked by...
Hello,
I manage to work with new S310 V2.
I use S310 for hrm only. Saying so also not for DFU service.
I have own proprietary method for transfering application images...
Hello, I'm using nRF51822-mKIT for a research.
To verify ADC readings from analog input, I've connected P0_5 to GND and ran the following code:
uint16_t adc_result;...
For my project I would like to use this bluetooth module: freqchina.en.alibaba.com/.../Fingertip_size_nRF51822_Module_Ultra_Low_Power_Bluetooth_4_0_Low_Energy_RF_Module.html...
I am trying to connect to a peripheral through s120 central and vendor has a 128 bit fixed UUID
I am trying to add it on central using sd_ble_uuid_vs_add(...,...) but it...
I am trying to develop an application for the Android that will communicate via BLE to a Nordic device. I'm able to read the characteristic's value by
BluetoothGattCharacteristic...
I'm using nRF51822 SoC and I have a LIS3DSH accelerometer connected to the ship via SPI bus . I used the SPI master example . So i used the switch_state() function then took...
Hi, I would like to know how I can immediately detect when a connection link is loss either from the central or peripheral. I need to know which error or notification to look...
Hello.
Here was the question about S120+DFU and Petter Myhre said that Nordic ready to release the new S120 version with the peripheral mode support, so making DFU OTA will...
Today I tried to update the SoftDevice of my project. I was working with the experimental NUS example with the old S310 SD (1.0.0). Because I want to communicate thru ANT...
Hello everyone,
I'm developing a security scheme in which the firmware verifies that the nRF51822 is the same as the one in the factory to which the firmware was installed...
Hi -- Can I run direct test mode on the nRF51-DK?
I've found the Direct Test Mode window in nRFgo Studio, but my board isn't available in the "Set up on ... " pulldown...
Hi,
I'm trying to implement a device including a PWM counter and a high resolution timer working with softdevice stack 110. Per the examples I got from this site, I'm using...
Hello! I'm trying to use s130 as peripheral.
I flashed nrf51822 with s130 stack. Opened peripheral example and build it with .ld file for s130.
After it I flashed this project...
we have a 2 chip soln. nrf for Ble, Atmel for main application.
config data is located in the Atmel part. Config data also has BT Device name, ADDR, Adv Params etc.
I...
