Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Hi,
How to upload and debug application program to the beacon with S110_nRF51822_7.1.0 and bootloader (DFU) using J-LINK? The standard procedure takes into account OTA...
Hello,
I want to detect the advertising data of more then one Beacon with the SDK51 and read the TX_Power for a location-application.
I´m inexperienced in stuff like...
will gazell device fall-back immediately to out-of-sync state upon reaching the max tx attempts even if the sync counter is still less than the set sync lifetime?
thank...
I got a nRF51822 based module and I loaded a slightly modified application based on "ble_app_beacon" example in nRF51 SDK via SWD interface using J-Link. The code has been...
Hello,
I have an application in which a BLE peripheral device will be essentially permanently paired with a client. The client will need to connect infrequently with the...
Hi,
I am trying DFU example on nordic evaluation kit using example on github:
github.com/.../DFU-Bootloader-for-nRF51-Evaluation-Kit
However, while compiling in keil...
SDK 7.2
S130 Alpha 0.9
I'm using the UICR customer register address 0x10001080 to stare a single 32 bit number. The code below is a bit of "brute force" to demonstrate...
Hi
I'm trying to make a new S110 BLE project for my nRF51 DK from "scratch" in Keil 5.14 (New uVision Project -> nRF51422_xxAC) , but every time i try to build the solution...
when I program wechat ble demo to my nrf51422 boards with S310 softdevice in Keil, return error like this "No Algorithm found for: 00000000H - 00007503H; Programming skipped...
Looking in the Keil Packs Installer, there are over a dozen entries for NordicSemiconductor::nRF... - each with its own version number.
So which one actually represents...
Hello
I'm trying to implement a number of different interrupts using the nRF51 DK but I'm having trouble understanding how to use the GPIOTE_IRQHandler function.
Basically...
Hello,
I read a while in this forum and found out it might be a little tricky to get I2C working when using a Softdevice. Is that information still valid or outdated? ...
I 'm using SOFTDEVICE.
Can I choose the BLE and NON_BLE while the applications running?
I want to implement, as below.
When I want to use bluetooth, BLE is run. and...
For a school project we have to develop a beacon system, to easy use different beacons we want to be able to change the major and minor from the beacons with UART communication...
I have seen this forum post: devzone.nordicsemi.com/.../
Which refers to this blog post: devzone.nordicsemi.com/.../
But when I use the Keil Packs Installer, and check...
