Hi,
I’m working on a Matter application using the nRF Connect SDK v2.9.2 . I’ve added the AirQuality cluster into my device with sub-sensors: CO₂, PM1, PM10, TVOC, and Temperature...
Hi Team,
Recently we did a network related testing for our CL5G modem (nrf9160) and observed a problem, in this test we used a nmap tool, this tool will search for open...
Steps to reproduce the problem
Create a new application based on the Matter Light Switch example of the SDK 3.0.2
In prj.conf set CONFIG_CHIP_FACTORY_DATA_BUILD=n
...
I would like to do a FOTA using bluetooth and external flash memory on nrf52840 board. I am also using sdk 2.9.1 The issue i am currently facing is I get the below when i...
Hello nordic community,
i have custom board that have nRF5340 and nRF7002, our requirement is to use wifi every 5 minutes (connect send data and disconnect) but randomly...
HI,
I am using the periodic_adv_rsp example from version 3.0.0. I would like to ask how to switch channels and transmission power in the example code?
Thanks.
Hi, I am using a nrf51822 with sdk 7.2.0 and s11o v7.1.0
I also have a imu ( mpu 6050 ) that gets accelerometer and gyroscope data.
How do I do continuous transmission...
Hi,
I am using the nRF51 Dongle and every time I send a command the pipeline goes into "Stall" condition. Using USBlyzer I can see that the command is sent but straight...
Hello,
I would like to build a device that looks for other beacons (not using a phone)... This device would simply look for other beacons near this device.
My questions...
I just tested putting the same firmware on two different nRF51822 s and inspected them with this test app .
They show two different UUID's.
I can find no macro...
Hello guys!
I'm experiencing some troubles trying to compile the blinky_rtx example for my new nrf51DK. The source is taken from the SDK7.2.0.
I'm under Linux and I...
I am brand new to nRF51 DK and I am struggling to figure out where to start. My goal is to periodically sample analog inputs and write them to SD card.
Can someone point...
Greetings,
Is there any way to increase the pairing distance needed for the host and device to pair. The application I am developing needs static devices, if they loose...
Hi there,
I am little confused about how the BLE interrupts work, when they are executed, and how can I explore their results.
And, what is the difference between on_ble_event...
Hi,
I am trying to get a PWM output via GPIO. I have been following this link.
devzone.nordicsemi.com/.../
and used the GITUB project as it is github.com/.../nrf51...
Greetings,
My name is Maria, I’m working in an application with the nRF51822DK to communicate via Bluetooth to the USB dongle (PCA10000) and send data between them. In the...
Hi,
I'm seeing a lot of this issue with iPad mini (1 gen), iOS 8.1.3.
Many times I start the bluetooth app, the connection just drops while doing service discovery,...
Hi,
I am trying to run event based UART. here is my code snippet:
void uart_callback(app_uart_evt_t *p_app_uart_event)
{
uint8_t rxbyte;
switch(p_app_uart_event->evt_type...
I'm getting started trying to use the device firmware update (DFU) feature of an nRF51822. I'm using soft-device (bluetooth abstraction) version S110-SD-v7.1.0 , and SDK ...
When I try to update the application on the nRF51422 chip over DFU, I have trouble with the bootloader.
I use the nRF Toolbox app to do the firmware update. I can select...
