Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
Hi,
On peripheral side i have S110 device with ble_bas service and custom base service. Both have notifications.
On centrasl side is S130. After discovering services i enable...
I want to use the pca10001 to communicate as a master to an accelerometer, but when i use the function spi_master_open i get a NRF_ERROR_NOT_SUPPORTED error. I get no clock...
Hi everyone.
I am working with nRF51 to make two BLE device, One act as cetral and another as peripheral.
I have implemented almost functions that the two devices are...
Hi,
Do all NRF51822-DK (development kit) have the same silicon build revision? If not, which distributor should I approach for the latest revision and is there a specific...
I have encountered a problem with the IAR linker where I run into a 32k code-limitaion, even though I have a licence with no limitations. According to IAR, the problem may...
I was playing around with examples and decided to implement a custom service that sends the RSSI as a single-byte characteristic value. Here's the init function:
static...
Hi,
I'm trying to connect to BLE and send data on UART. I'm using nrf51422 with softdevice s310 and SDK v5.2.0.
The following code gives me error 3003 which I figured...
Hi,
I think getting started with the Nordic chips is not as easy as some others.
I would like to know what are the first things that I need to run my code on a Nordic? Especially...
I just got the nRFgo Dev Kit, and going through the set up I see I need a nRF6310 Motherboard, but I can't seem to find anything about it - like were to buy it.
I just downloaded their iccv8cortex trial version and it includes the 51822 as a target. My 5 minute test drive not withstanding, it looks like this might be a good option...
How to reduce power, for bond connections such as cscs services which only requires communication once per second?
Is there a way to manually / automagically turn off the...
Before I call sd_power_system_off(), I do the following:
NRF_TWI0->ENABLE = 0;
NRF_TWI1->ENABLE = 0;
NRF_ADC->ENABLE = 0;
NRF_SPI0->ENABLE = 0;
NRF_UART0->ENABLE =...
Hi
I using nRF51822 ble_app_uart project with softdevice 7.0.
I need to manage my internal flash memory map so i cannot use pstorage libary test main.txt .
So i try...
Hi,
What is the typical range of operation that can be achieved by nRF51822 Bluetooth Smart Beacon Kit ? I know it depends on the Tx power, but can a range of approx 30ms...
