Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
I'm looking for a way to use the nordic uart service ( devzone.nordicsemi.com/.../ble_sdk_app_nus_eval.html) from Linux using the native Linux BLE Stack (BlueZ). My application...
Hi,
I've created an application using the S110 experimental ANCS demo. I successfully implemented ANCS and then began to structure my application around it. At some point...
Hi
I have some problem about the HomeKit SDK,is there anyone could help me?
In the HomeKit SDK,such as lightbulb project,there is a function mfi_i2c_configure that...
Hi Nordic guys,
we are developing a peripheral device with a custom protocol to exchange data.
we are using nrf51822 with SDK 6.0 and SoftDevice 7.1.0 (s110 being peripheral...
I can not find information about layer stack-up and whether the via-in-pads were filled, please provide this information. We are thinking about a variant with thin outer layers...
Hi, I am trying to combine SPI, microESB and BLE. BLE and microESB will not be combined in realtime, but rather be two distinct modes, and not run at the same time, and therefore...
[test result] change to use Timer1 of timer example,it failed. if you use timer0, it is OK..
SDK IS 9.0:
nRF51_SDK_9.0.0_2e23562\examples\peripheral\timer
[test step...
Is there a way to access the lower level clock which a connected slave uses to stay in sync with the master. We want to use this to keep our PWM in sync. We are looking for...
Hello,
After looking into forum regarding usage of S130 stack for using the device as both central and peripheral, I understood that the peripheral and central can concurrently...
Hi All,
I have query regarding PWM usage in nRF51-DK. I have a requirement to control 3 LEDs (brightness and power) simulatneously. I intend to use PWM for the same. But...
Hi there! An error occurred in device manger. It was caught at the first APP_ERROR_CHECK in device_manager_evt_handler. Error code is 0x88. I can't find this error code in...
Hello,
I do not see the bootloader files for this example in SDK 0.9.2. Where can I find the boot sequence for the ble_app_hrs example, and in what files is the boot setup...
Hi,
I don't see in SDK 0.9.x any examples pertaining to accelerometer peripherals. I see a TWI sensor example from the nRF51, but I am working with the nRF52. Are there...
The nrf8001 datasheet seems to mention that there should be no connections when sleep command is sent. So I wanted to call aci_disconnect first. But what reason do I use?...
Hello,
I received the nRF52 DK and tried setting it up as described in infocenter-->nRF52 Series --> Get Started.
I have the following installed:
Keil uVision5
Error...
Hi,
I noticed that I'd occasionally hit an error when calling into nrf_drv_spi_transfer using the SPIM driver (SPI0_USE_EASY_DMA set). nrf_drv_spi_transfer was returning...
