Hi Team,
we are using two nRF5340 Audio DK kits to test LE Audio CIS example (unicast client & server).
kit1 nRF5340 Audio DK - act as gateway ( connected to PC/shared...
Hi all,
I want to fully understand the concept of Bluetooth protocol using nrf52811. Any advice will be helpful for me!
First, as I understand softdevice is Bluetooth...
Hi，everyone:
We are developing a Nearby protocol combined with UWB, which needs to communicate with the Bluetooth of Apple phones and then use UWB to measure distance. We...
As shown in the figure, MCUboot has a boot_go_hook function. I'd like to define this function in my own project and compile it into MCUboot. Since I'm using single slot DFU...
Hi,
1.In ncs v3.0.0, can both USB DFU and UART DFU be enabled simultaneously on the nRF5340 DK board? 2. If USB and UART DFU can be enabled simultaneously, then how should...
Hello,
We are working on establishing a connection between one of our existing Bluetooth modules (cypress) and nordic based module to provide backward compatibility with...
Hello,
I’m working on a project based on the nRF Connect SDK v3.0.0 Matter Light Bulb sample , using the nRF52840DK. I aim to implement IPv6 support and enable Matter over...
As indicated in the PS, System On Mode idle draws only 2.6 uA.
Does this mean that if I install and active a timer interrupt, where the interrupt routine places the system...
Hi,
I am new to ARM development. We are thinking of ordering mkit for evaluating and developing a custom BLE service(profile) which sends data to BLE client (probably a...
Hello Everybody!
I have been working with BLE security and I have an issue with OOB setup.
I'm setting my nRF with the following:
m_sec_params.timeout = 30;
m_sec_params...
I was reading this press release:
http://www.nordicsemi.com/News/News-releases/Product-Related-News/Single-board-Bluetooth-Smart-Arduino-solution-is-low-cost-and-can-be...
Yo!
I'm very concerned by what I hear about Bluetooth Low Energy security. According to this guy , who presented a paper on the subject at a USENIX conference last year...
Any experiences about analog sensor LM35DZ? I used this example: main.c
The LM35 data sheet says it will operate from +4V to 30 V supply. I'm use supply only Vcc pretty...
Hi all,
this is not a question per se but rather a warning to those who are attempting to debug Flash related operations with the SEGGER J-Link GDB Server (v4.84a for Linux...
I'm using API 2.1.3 and I'm having problems with SendData blocking forever at the end of a process. I placed access mutexes around each method call to the library, as well...
Dear Nordic Developer Zone,
I have modified the ble_conn_params.c file in order to be able to negotiate new connections speeds between IOS app and Nordic nRF51822 chip...
Hi,
Regarding the bond_info_store() routine, I am having issues where after several calls to this function (client pairing forget/reconnect), my p_bond gets corrupted. This...
Hi, I am developing a BLE application using SPI and TWI. (Using nRF51822)
This discussion is about my survey in development zone for future develop the TWI part.
I want...
I'm calling ble_bondmngr_bonded_centrals_store in response to BLE_GAP_EVT_DISCONNECTED as is the case in plenty of sample code, but when ble_bondmngr_bonded_centrals_store...
Hi Guys,
I have managed to get the BLE DFU demo service working fine (dual bank) on nRF51822 EK. I use a Linux Python program ( bitbucket.org/.../nrf51_dfu_linux) (with...
what is the detection speed, when the beacon
enters into a wall unit area? With their 868 beacon they can
detect in 0,2 seconds. Is the nRF51x22 in sleep mode and does it...
