Hi, we are developping a medical device that receives an audio stream from a smartphone. We have a custom board connected to a different DSP than the one in the nrf5340_audio_DK...
Hi! We're testing nRF7002 with the nRF7002-DK and NCS v3.0.2. CONFIG_NET_ZPERF=y has been added to the nrf/samples/wifi/shell/prj.conf, the rest is untouched. Running that...
I am using the nrf5340 on a nrf7002fk dev kit. I am interested in low power operation so I am measuring the power consumed.
I am running a simple app:
int main(void) ...
Hi,
I have a simple question about Bluetooth Channel Sounding:
Question: If I use BT_CONN_LE_CS_MAIN_MODE_3 as main mode (PBR + RTT), does it make sense to use sub mode...
Hello Nordic Team,
I am currently working with the NRF54L15-DK. I have successfully configured the simple ADC on AIN4 (P1.11) and am able to read the raw sensor values....
Hello Nordic Team,
I am currently working with the nRF54L15 DK and interfacing an occupancy sensor over UART. In my standalone application (non-Matter), the UART communication...
i am working on custom board nRF52840 with display ST7789 + touch Ft6336
1) i want to use LVGL library with Display how do i get started with LVGL .Any tutorials or sample...
I was learning GPIOTE using the example provided in SDK 9.0.0. (examples\peripheral\gpiote). The example only uses GPIOTE task and a timer to drive the task through PPI. ...
We have created a firmware and encrypted it with a private key and made it public. When we download it to the chip it's decrypted with a public key stored in the chip. Right...
I have about 200-300 sensors, each requiring to send data at around 0.5-1Kbps to a central node (coordinator/master node), what will be the network configuration/topology...
In SDK 8 for the nrf51422, notifications are always being sent as 20 bytes, regardless of p_len. The BLE_EVT_TX_COMPLETE event stores the proper number in tx_length, but the...
Hi everybody.
I am making an application which combine ANCS and UART on PC100028 (nrf51 SDK 9.0.0). This program worked properly. However when I add DFU service (dfu_dual_bank...
I am currently using Nordic's UART code and wish to build to use the UARTE rather than the legacy UART. I am currently using the following definitions in nrf_drv_config.h...
I use the S110 V7.3.0
I use the uart function ,I can use the uart function is OK.
But ,I need save power.
How can I turn off the uart function,while I was start the uart...
Hi,
When trying to update an application using nRF Toolbox on iPad, I get the error as in
this thread .
Turning Bluetooth OFF and ON does not help. On Android it works...
I tried the latest SDK 10.0 and Softdevice 8.0.3. I compiled UART_OVER_BLE examples and it works well with Android and Windows Mobile phone. However, when tested with iPhone...
Hi,Nordic and all great guys,
I am a new developer for NRF51822, and quite unfortunately ,we have a complex application to develop. We need to run code in the main thread...
Hi,
I know how to change the name of the device using
BLE_GAP_CONN_SEC_MODE_SET_OPEN(&sec_mode);
err_code = sd_ble_gap_device_name_set(&sec_mode,(uint8_t const *) DEVICE_NAME...
Hi,
I am developing a custom profile for an application.
This custom application works fine with Master Control Panel and nRF toolbox on Android.
I am also developing...
Hi,
I am using the sample ble_gls code from Nordic.
Currently it advertises for 180 sec and than resets or goes into sleep mode.
If i want to advertise continuously what...
Hello,
I am just starting working with the nRF52 development kit and have a couple guidance questions. I'm very new to the Keil environment and am having a little trouble...
I'm using s130_nrf51_2.0.0-4.alpha as central and do some testing with channel map.
I set the channel map before I'm trying to connect to a peripheral with:
ble_opt_t...
