Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command： west build --build-dir build . --pristine --board nrf54l15dk...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
Hi,
I'm trying to run the uart loopback example in the nrf52 0.9.1 SDK with DMA enabled but it is being caught in an error catch. It runs fine without DMA enabled though...
We have some NRF51-DK devices here.
Recently we upgraded our segger software to v5.00.
During programming using nrfjprog we got the question to upgrade the emulator firmware...
I am trying to write a simple advertisement application for my nRF51822 development board (for it to run on an S110), but the tutorial on the nordicsemi.com website, which...
we are making a pedometer. when you are connected, you get notification for every step you make (just an integer)
you just did 50 steps. you can see it in the app. now...
I'm trying to implement a wake-up button on central multilink example. I.e, i need to implement the app_button in order to wake up from sd_evt_wat() function. The problem...
Please can any one tell me from where I can get this programmer? Nordic have stopped selling development boards in which we can get the programmer. I think this could be a...
Hi all!!
sorry to trouble you with this but I work over it for the last 3 days and no breakthrough..
I am using a nRF51DK with the MBED program. I am trying to download...
We are a contract manufacturer. We are trying to help one of our customer's with their bare board design which uses your NRF24L01+ (NRF24L01P) that comes in a 20-pin 4x4mm...
Hi!
We are currently writing a simple bootloader which reads the new application image from a external SPI based flash memory. We are using the S110 SoftDevice, which works...
Hi All,
I have been developing a bluetooth chip based on nRF51822 QFAC. I have followed the design rules very closely but at the end I do not get any bluetooth signal coming...
main.c Hi ,
I'm using nRF51822 and S110 stack and sd_6.0.0.
having an ble app UART example.
Facing a strange problem that when (from nrf Uart App)connecting and disconnecting...
Hi
I set one GPIO interrupt with low-to-high sense, but seems it did not triggle the interrupt when SD run.
I want to confirm the SD would make the interrupt loss? If so...
Hi folks,
I have a 2MHz clock (call it DRDY) coming into my nRF51 on one of the GPIO pins (call it AFE_DRDY). I need to read an external AFE chip on every falling edge...
I have a project where specification requires disconnecting immediately after sending a response to a BLE read request. I'm using authorized reads.
Currently, I'm using...
