We encountered some problems while debugging the nRF54L15. A total of 10 circuit boards were produced, and the chip on the board is nRF54L15CAAA. After programing the code...
Issue:
I would like to bring to your attention that I am getting an error when running the 'list command using the nrfcredstore cli utility, while trying to retrieve the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
Hello everyone,
As the title suggests, we're trying to get the on board flash (mx25r64 as far as I can tell) of the nrf7002dk devboard working as a USB mass storage device...
Unable to Install or Launch nRFgo Studio Win64 1.18:
Downloaded "nrfgostudio_win-64_1.18.0_installer.msi
Installed package on a 64-bit Windows 7 PC as a 'regular...
I'm playing with the SDK 8.0 HRS peripheral example.
There is a config folder that contains device_manager_cnfg.h. But this isn't being built into the project, the version...
Hello,
I am currently trying to write my frist few lines of code.. I started with the ble_uart example and then mixed in some code from the spi_master example.. I wanted...
Hello,
why did you chose to remove the S130 1.0.0.3-alpha from the relasenotes and merge it with the latest version? I don't think that's the way it works. Now we have...
Hi All !
I was read many posts about this function and do not understand how to check if all data is deleted.
In my situation I do:
Start advertising for bonded...
My devices in the field have firmware that saves an error code when it gets thrown and then sends it to a central so that I can see if there are errors with devices in the...
Hello,
I am using the sd_flash_write function. If I use this function without the nrf_delay_ms() function (see code below) the data is not being written.
sd_flash_write...
I would like to know if it is possible to log realtime sensor data to flash while advertising. I would like to have a device which transmits real time ECG data over ble UART...
Hi
I am struggling to change the device type on examples setup for nrf51422 to nrf51822.
If I change the setting in "options for target"/device I get the failure message...
I changed the multilink central example to some custom code. However, it seems like I've run out of space. But I don't under stand how this is possible because I selected...
Using gcc-arm-none-eabi-4_8-2014q1-20140314
Using nRF51_SDK_8 Using nRF51 dongle
Build in nRF51_SDK_8/examples/peripheral/blinky/pca10031/s110/armgcc succeeds...
Hi there,
When i disconnect the keyboard, the nrf51822 will restart advertising in directed mode.
And then on_adv_evt() will receive BLE_ADV_EVT_PEER_ADDR_REQUEST event...
Hi,
I want to use BLE for following situation and I wonder if it is achievable.
I have a 3 boards with nrf51822. Two of these boards have mpu6050 sensors connected to nrf51822...
Hi,
I am a little confuse at the moment and wondering if anyone would have any insight on the matter.
I am making a pair of device with s110 and s120. So the s120 will...
Hi,
I'm trying to write my own application based on the ble_lbs example on nrf51822. Recently I've discovered a problem with reconnection to the beacon. I can successfully...
