Hello,
Is the NRF7002 pre-certified for the RADIO EQUIPMENT DIRECTIVE 2014/53/EU (RED directive) ?
Is there a recommended antenna design that would ease certify a product...
Good day, I was attempting to test the radio performance of the NRF54L15. I ported over the Radio_Test sample project to try and transmit an unmodulated carrier wave at a...
My task is to mount a littleFS system on the external flash memory, so I can save files.
I am using the littlefs filesystem sample from
zephyr/samples/subsys/fs/littlefs...
Hello.
How often are the LQI and RSSI values in the coordinator updated for a child?
Preferably I would have liked to get some kind of notification every time LQI and...
Hi,
I want to configure P1.02 and P2.06 as normal GPIO for my nrf54l15 custom board. For this I have added the following in my .overlay file
From https://devzone.nordicsemi...
Hi Nordic team,
I’ve been working with the nrf_dm sample from NCS 2.9 to perform distance measurements using multiple nRF52840 devices. The sample works well, and I've made...
Hello
I'm working on a custom electronics board with an nrf54L15 (QFAA). This MCU is interfaced with an EEPROM memory (24FC16T) via an I2C bus connected on P1.03(SCL) and...
Hi
I'm starting with NRF51822. I'm going to develop a costum PCB using this chip. I'm a bit confused because searching on the forum I saw that I need a product key to use...
Hi,
I'm running Mac OS X 10.10.2 with the nRF51-DK PCA10028 card that I received today. I started off following the instructions in this article , and was able to get JLinkExe...
Hi all,
I am using the multi role example ( github.com/.../nRF51-multi-role-conn-observer-advertiser) to scan and advertise concurrently.
I was wondering if the scanning...
I have a 16MHz external clock oscillator to drive a micro controller in my system. Can this also be connected to the crystal input on the nRF24L01+ to drive it's clock? Should...
Hi All,
I wanted to write a patient record to glucode measurement charateristics from android Phone which supportes BLE features . How do i write a record to BLE device...
When using the OTA DFU using the button press implementation is it possible for the bootloader to require bonding? I figure I can use the preserve app data functionality built...
Just took the developer.mbed.org/.../ code and run it on the board.
But when I try to connect with my phone I get: "Device doesn't support UART. Disconnecting".
What...
Hello,
I am using the RedBearLab's BLE Shield 2.0 and I'm trying to modify the advertisement data using nRFgo studio to include manufacture data (type: xFF) for one of...
Our IC nRf51822 has an identifier "QF AA CO" (IC rev 1) The document "nRF51 Series Compatibility Matrix", Table 4, shows the maximum version of the SDK 5.2.1 and 4.4.2 SD...
Hi guys,
I install V1.6 nRF ToolBox apk in my Android phone, and want to do the DFU operation.
When the device in DFU status, I select the target HEX file but it shows me...
We are configuring the watchdog like this:
// Watchdog
NRF_WDT->CONFIG = (WDT_CONFIG_HALT_Run << WDT_CONFIG_HALT_Pos) | ( WDT_CONFIG_SLEEP_Run << WDT_CONFIG_SLEEP_Pos...
So I've got this long characteristic which takes several read operations with offsets to read it completely. Idea is to have it refreshed only after the client has read it...
Hi all,
I've have written a debug version of our application firmware to catch any and all error seen during operating. The most common one I see is NRF_ERROR_BUSY stemming...
Hello,
I am doing some tests with the Heart Rate Service Sample Application for the nRF51822 evaluation board (PCA 10001). Inside the ble_stack_init(), there is this call...
