Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hello,
We are working on Zephyr sample app Mesh on nRF52840dongle with nRF Mesh application.
After going through the documentation and few other Q&A on the portal, I was...
Hlo
I have designed a custom board based on nRF5340. Now I am trying to do flashing and RF testing of it through nRF5340 development board but can't even flash it because...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
We are developing a product that will have a wireless and wired option, based on the NRF52840
The strategy is to release the wired option first, followed by the wireless...
Hello,
I'm trying to build the trusted firmware M for the nrf9151.
I did the following steps:
git clone git.trustedfirmware.org/.../trusted-firmware-m
cd trusted...
Hi.
I working a central and peripheral device which will connected with 4 sensors. sometime after disconnect and reconnect. the device will got fatal error in service...
Hi, I am using NRF connect sdk 2.6.1 and I am wondering what is the best way to run crypto operations when using TFM profile type minimal and building for nrf9160_ns. TFM_PROFILE_TYPE_NOT_SET...
I want to measure the current consumption on the DK with an Amperemeter. For that i have this setup:
Please excuse my terrible drawing skills. Im basically powering...
I am using NRF52810 as a beacon tag.
I want to apply AOA technology to this tag, is it possible?
I'm confused because the nrf52810 says it supports BLE 5.2.
Hi,
I'm experiencing memory constraints while using the nRF52811 with the SoftDevice S112, as it takes up a significant portion of the available memory. Is there a lightweight...
Hi,
We developed an application on the nRF52833 and are now porting it to the nRF54L15. As part of this process, I'm integrating an external RTC via I2C on the nRF54L15DK...
After purchasing the PPK2, I connected the Fluke287 and PPK2 Ampere meter in series to check whether the measured values matched the Fluke equipment.
The Fluke287 consistently...
Hi
I have run nrf5340 WiFi shell project in ncs2.9.0, everything ok if use Logging UART0 for cmmands(wifi scan/wifi status/ wifi connect.....etc)
now I need to use...
Hello all,
I have slightly modified the coap_client sample from the SDK such that the main function is being called on certain actions from another program. I'm getting...
I use the gpio8 interrupt to detect whether the SD card is inserted. When a falling edge is generated, it means that the SD card is inserted. But I found that sometimes, the...
So I have been doing a project on nrf52840dk, So I have built a custom bootloader for it as well, I have been trying to add the custom bootloader with the code in my nrf52840dongle...
Hello,
I have a question about the NRF SDK fundamental lesson 8 exercise 1. In the code below get_access and release_access are executed in different threads. The semaphore...
Hi!
Is there samples for specifically make nrf54L15 show up as 2 mics for stereo audio source through bluetooth? My project require lot of development with mics and I...
Hello.
I am testing UART connectivity using the nRF54L15DK.
After assigning pins to TX and RX, there were combinations that worked fine and combinations that didn't. There...
Hello！
I'm writing a program that performs both advertising and scanning simultaneously. I've configured active scanning and scannable advertising, but it seems that scanning...
