Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
We are upgrading some products to SDK 14.2 and creating some new ones.
We need to start production programming of boards. I can't find the information on how to do this...
What is the maximum and minimum frequency of the PWM signal/square wave that can be measured on the NRF 52DK board I'm using NRF 52832.
Also, what is the max and min "pulse...
Hello,
I have found similar questions on transmitting multiple bytes over SPI, but I am still not sure how to do it. I want to communicate with a driver which needs to be...
Hi,
I found the 'Solar Sensor Beacon' example from
https://github.com/NordicPlayground/solar_sensor_beacon .
There, I found that no softdevice initialisation (nrf_sdh_ble_enable...
I am working through the nordic sdk 8.1 peripheral heart rate monitor example. I am wondering what RR is? I can't figure out what it stands for or what the purpose of it is...
Hi,
In my current project I have indicating LEDs connected via TWI bus. In this case, I can't use BSP_LED_0/BSP_LED_1 outputs to indicate states as it implemented in nrf_ble_dfu...
Hello, I recently use nrf52832 to make a wireless sensor network of BLE concurrently with NRF_ESB.
During development, I use only 2 sensor. Both sensors are connected to...
ANT S212, nRF52:
I've read all the links in the forum regarding serial port running in debug mode and not in run mode.
In my case, it works in RUN mode until softdevice_setup...
Hi
I have a sensor array which data have to be advanced burst to one or many devices.
The array size is anything from 24 bytes to 24k bytes, depending on the number of...
Hi guys,
I am using nrf51822 and SDK 11. I have some trouble about suddenly reset the nrf51822.
In my application, I used uart_fifo to received some information from other...
Hello beacon fellows,
with regards to maintenance, i am looking into the possibilities to avoid human presence when updating the message to be emitted by Beacon Kit. Any...
Hi,
I'm trying to do (customized / simplified) dual bank DFU on NRF52832 as simple as possible, without any complicated checks.
Assume I succeeded into storing the new...
i want to know about how nrf51822 beacon's states will change once it is turned ON.
with the state diagram i can define how the module is working after turning it ON.
...
Hi,
I am trying to configure the nRF52832 on my custom board to work on the 32.768KHz clock signal from the host controller. I have configured the LFCLKSRC register to use...
