Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
Hi,
I am trying to use random number generator as implemented in ".../examples/peripheral/rng" from SDK14.2 in a project but receiving compile problems as shown below. ble_app_hrs_rscs_relay...
Hi,
I noticed that my current NRF52 based prototype is consuming 4.5mA as soon as I enable the BLE functionality, when its off its only 1.6mA
I send the chip to a sleep...
Hello !
I was wondering How the interval connection was calculated in the Android application nRF Connect ?
Do you use a special/ hided function ?
I tried to get it...
Hello,
I want to set up client and 3 servers which will send data from sensors to client with high data rate. Currently I am testing light switch example from Mesh SDK 1...
Hi,
I am using nrf51822 with SDK 12.2.0. As of now, we are using RL-51822-A1 for beacon as well as scanner.
But, we are not getting stable pattern for RSSI at 2m, 4m and...
Good day!
I am working on a custom board which has NRF52 and am using SDK 12.2.0 and in that, I want to stream BNO055 data. The base code I'm using is ble_app_hrs. The problem...
I want to set gpio using one interrupt and want to clear it using another interrupt funtion?
It seems i can only use the toggle funtion ,if i use the nrf_drv_gpiote_out_set...
Problem Statement: For one of our requirement we have to switch tx power in steps in ascending order continuously.
We are using ble_radio_notification feature to achieve...
Hi,
I'm trying to receive sensors data from three fdc1004 that have the same address. Can you have three TWI interfaces at the same time? How do you modify the nfr_drv_twi...
Hello,
I've just started using Segger Embedded Studio v3.30 for my development and I've been having trouble setting it up. I followed the instructions in this blog but...
Hi, I am programming on Thingy 52 to try to get it work like one of my nRF 52840 DK. Basically, I want Thingy to send beacons with data periodically and another Thingy to...
I have followed the tutorial given in the Nordic Devzone for using eclipse and haven't faced any problems while compiling and uploading the example "blinky".
I made sure...
Hi, ,
I am working on the nrf52832 development kit and want to program it as an I2C master. I have download the nRF SDK v12.3 but I am unable to understand the code written...
Hi guys
I am wondering what could be better for my system:
Multiples nRF52 central and peripherals (uart input/uart output to simulate keyboard and display)
SDK 13 ...
HI,
We use nrf52832 on a device with sdk 14.1.
Our product has to work at different temperature (between 20 and 70°C).
We did some measure and found this :
...
