I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hi,
I have been using the following parameters to flash program the example ble_app_uart_c_s130_pca10028 (SDK 9) but the problem is the it uses the S130 v1.0.0 softdevice...
Hi,
I have a newbie question. Is it possible to implement a POTS voice quality like an intercom system using Thread (assuming all the end points are using nrf52840 SOC...
We are trying to minimize the UART current in our product, so we tried some experiments on the PCA10040 board.
We noticed a significant current difference between SDK11...
SDK14.2.0 sd132v5.0.0 nRF52832
I've looked for a solution to my issue on the discussion forum, but can't find an answer. I am working with the buttonless DFU peripheral...
I have two nRF52832 devices. One of them I have been using for a while and the other is brand new. My BLE application will flash and run just fine on the old device but not...
Hello,
I read in your datasheet the follwoing:
"32.768 kHz synthesized from HFCLK (LFSYNT)
LFCLK can also be synthesized from the HFCLK clock source. The accuracy...
Hello,
in the Online Power Profiler , the current consumption increases, when the voltage is reduced. What is the reason for this?
Isn't there any documentation on the...
Hi
I need to capture a serial bit stream which consists of a sequence of 16 bit words, package them up and transmit over a bluetooth interface - it's a datalogger application...
Hi!
I have some troubles with making embedded serial port working on NRF52-DK. Basically I can receive data sent by nrf chip but I cant write. When I write something using...
More of a suggestion than a question:
Using the info available on the infoCenter, especially here and here , I'm trying to implement a way to dynamically select the DFU...
I use Adafruit Bluefruit library and developing code to run on Fanstell BT832.
Up to know i have been able to compile several examples and run it on the NRF52 DK board....
Hello! I am new to the Nordic and Bluefruit enviroments.
I am currently working on getting a scan response request from the scanner to the advertiser and have the advertiser...
Hello devzone,
There are 3 {37,28,29} channels for advertisement & i want to advertise only on 37.
Soft: Nordic mesh v1.0.0 stack & pca10040 nrf board, light switch example...
Hi, I'm trying to controll the port of my nRF52832 by writing to a characteristic value. So far everything works fine but I'm unable to get the value of my characteristic...
