Description:
My nRF52 DK has stopped being recognized by my PC. Below are the details of the issue:
Kit Info: PCA10040 v3.0.0 (2023.22), nRF52832 target MCU
...
Hi，
I am using nRF54L15-DK for Zigbee light_stwitch startup testing. After successfully connecting the development board to the Hub for the first time, I evaluated the time...
Hi
I have a code previously can be built in NCS 2.91:
However, when I use the new NCS 3.01, it can not be built, the error is:
Could you please help me figure out...
hello everyone I have implemented BLE, ADC, RTC, and UART. After that, my power consumption is around 1.31 mA. Can you suggest possible ways to reduce power consumption or...
Hi,
I am trying to integrate the nRF5340 Audio application (CIS Unicast Server role with bidirectional streaming enabled) from NCS 2.9.0 into on my custom nRF5340 based...
I'm attempting to write software onto a newly purchased nRF52840 dongle using nRF Connect for desktop, but I'm unable to do so. My environment is Ubuntu 24.042 LTS. The LED...
Hi,
We occure a problem that when we integrated HID,Tile and battery service, open nRF Connect by iPhone, we cannot connect with the EVB and show connecting. But when we...
To read the MAC addresses defined I use the following code (with CONFIG_BT_ID_MAX =2 in prj.conf):: :
bt_addr_le_t addr [ CONFIG_BT_ID_MAX ]; //space for random address...
Hello,
We are using Raspberry Pi + NRF52840 as Borderrouter for Openthread using Radio Coprocessor design.
However we are facing stability issues on the RCP where it...
I am using nRF52833 PCA10100 board. While trying to run sample ble code in segger embedded studio, I am frequently facing this error which says, .text file is larger than...
I have implemented DFU functionality in my Bluetooth mesh project and used device A as the distributor and device B as the node to be updated. I have already configured both...
Hi,
I'm developing my app on nRF52840, NCS2.7.0 on VS Code 1.100.0.
My application needs to save settings data (4 x int32_t ) to external the NOR Flash (mx25r64) in `settings_storage...
Hi,I am using NRF54L15 DK in which I need to transmit audio data over BLE where that data will be used for only plotting in application,I am using sampling rate of 16000 and...
I have an app running the S132 softdevice, doing most of the applicatino work in a routine being called by an 8 Hz app-timer. Under certain conditions that I detect with external...
Hello! Introduction. Responsibilities of the cores in my device: 1. app core. 1.1. data processing from a stereo microphone 1.2. data sending to net core. 2. net core. 2.1...
Hi,
I have set up a destination in the the NRF Cloud Message Routing Service
The destination has been verified and I can successfully send the test message from NRF Cloud...
We are trying to evaluate nrf9151 for working with Soft-SIM. Are there any instructions for configuring the Soft-SIM through AT command mode, or do I need to use another mode...
Hi，
I am using nRF54L15-DK for Zigbee light_stwitch startup testing. After successfully connecting the development board to the Hub for the first time, I evaluated the time...
I am currently working on the secure_bootloader example (pca10056_s140_ble) for the nRF52840 DK board and am encountering an issue with updating the OTA application. I have...
Hi
I have a code previously can be built in NCS 2.91:
However, when I use the new NCS 3.01, it can not be built, the error is:
Could you please help me figure out...
hello everyone I have implemented BLE, ADC, RTC, and UART. After that, my power consumption is around 1.31 mA. Can you suggest possible ways to reduce power consumption or...
