Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
I've seen other threads about the issue:
- https://devzone.nordicsemi.com/f/nordic-q-a/117267/light-bulb-sample-works-on-nrf52840dk-and-doesn-t-on-nrf52840-dongle
- https...
Here is my script for programming. Does the sequence is OK? or any advice to improve?
nrfjprog --eraseall
nrfjprog --recover --family NRF53 --coprocessor CP_APPLICATION...
Using the peripheral_uart example routine from the NCSv3.0 library with the 54l15 chip.
1. compilation command: west build --build-dir build . --pristine --board nrf54l15dk...
I'm looking into a rare issue on the BBC micro:bit V2 which uses the nRF52833 as its (application) microcontroller. I used to be familiar with some CPUs from the 80s but my...
Hi, I have a Nordic nRF52 Development Kit. The ADC examples work, the LED examples work, and the NFC examples work. However, none of the Bluetooth examples work. The LEDs...
My DevKit arrived today. Very nice.
Plugged it into my mac, immediately recognized as USB device. Flashing LED, mounted as storage device, etc.
Tried to enter Bootloader...
Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
Hello everyone
I am trying to configure the write values like in the link loss profile it is possible to write no alert, mild alert, high alert, similarly i have created...
Hello!
I would like to know if it is possible to send an unique Gatt message that contains notification enable for multiple characteristics.
For example,
buf[0] ...
Hi Nordic,
I posted the issue with BSP package in devzone.nordicsemi.com/.../
unable to attach the main.c file mainOriginal.c
HI Aryan,
Thanks for your reply. Its working...
main.c HI Nordic,
I don't want bsp.c in my project. So I removed the bsp.c and included custom_board as mentioned in devzone.nordicsemi.com/.../
I am also using UART for...
I have the nRF52 dev board "PCA10040".
I downloaded "nRF52_SDK_0.9.1_3639cc9" SDK.
I noticed that there is no installer for the SDK.
I unzipped the SDK and using Keil...
Hi all,
Since I will use broadcast way in RF transactions between one NRF24LE1 based senders and serveral NRF24LE1 based receivers . I was told not to use "Auto ACK" in broadcast...
I'm new to Bluetooth LE, Python and C. I have the S130 python examples for heart rate testing. I am attempting to modify the heart rate collector code to act as our central...
I am able to use pstorage_clear and pstorage_load without any problems, but whenever I try to do a pstorage_store the callback function is not being invoked. This problem...
-Essentially I want to do a device firmware update on to the nrf51422 using my Android phone (the nrf applicaiton). I am using your sample code for a project that my company...