I am using nRF Connect SDK v2.4.0 and an nRF5340 DK set up as a PAwR advertiser. Is it possible to specify the channels to use in the Periodic Advertising train? I found the...
Hello! The PCN 219 rev 1.1 says "The new device revision of nRF54L15-CAAA is not drop-in compatible with the current revision, requiring update to PCB schematic
and layout...
Hi,
I am encountering an issue with the TWIM driver when attempting to communicate with the nPM1300 PMIC via I2C.
This problem seems to be related to the behavior of the...
I have been trying to implement a way to wake the system up after doing sys_poweroff() but no matter what nothing seems to work. I already tried many examples and none of...
Hello,
I have been able to get FW OTA to work perfectly well over BLE using
CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU =y
Now I am trying to display the update progress...
The custom AT command "AT%XICCID" was added in modem firmware v1.1.3 for the nRF9160 and was available from the first release for the nRF91x1.
This command provides a processed...
My task is to mount a littleFS system on the external flash memory, so I can save files.
I am using the littlefs filesystem sample from
zephyr/samples/subsys/fs/littlefs...
Dear Sir/Madam,
I am playing with SDK12.2 on PCA10028 board and runs its HRS example. This example has a battery service and its battery level characteristic could update...
I use DFU. All ok. But I need to store my settings after update. As I was advised, I located my data from address 0x72400
But Keil added after this struc some code
...
Please Find the Attachment Screen shot of SDK Document for Advertising Module. Also Side by Side I am doing Code Walkthrough Blinky Peripheral . The Code in Blinky No Where...
Hi,
In function advertising_init(void) , I have set
and in function gap_params_init(void), I have set
still the icon doesn't change. What could be the possible reason...
Hello,
I'm trying to program my custom board with a PCA10056 following this scheme (Note that my custom board is powered by the PCA10056) :
VDD (PCA10056) ---> VTG(PCA10056...
Hi,
I'm using nRf52840 rev B and C chipset and not able to detect the NFC on the device (the rev A chipset is working). Following SW combination is used:
nRF5_SDK_15.0...
Hello,
I am working on Multi-link. I want to scan the advertising information and connect only the uuid I set up.
I want to process it on_adv_report (), but I do not know...
The output order of my scanning Saadc is not predictable.
I found two related questions, but they both are for SDK 11 and seem to have been resolved.
devzone.nordicsemi...
Hi,
Am I right that after provisioner done with network configuration all nodes save their info in persistant storage and continue work without a provisioner?
How provisioner...
HI
i'm trying to use TSL2561 sensor, but i can't geting to work. I found the code that works on the psoc that, I change it so it fits nrf52840 but it still does not work...
I want to be sure about erasing flash. Flash is divided into pages and each page has 8 blocks. The smallest amount of flash you can erase is a PAGE. Is this correct. In other...
hello,
I'm currently stuck with sd_app_evt_wait() function leaving for an unknown reason. This function is called in the main loop.
The only reasons that shall exit the...
BLUETOOTH SPECIFICATION Version 5.0 | Vol 3, Part H page 2321 Figure 2.4
According to the figure, if an eavesdrop device exists in the pairing process, it is easy to obtain...
Hi support team,
I am currently working with the nRF8001 that I wanted to integrated on a my PCB.I would like to know if you have an antenna to recommend to work with the...
