Hello,
We’re Bachelor’s students developing a project to estimate the angle of arrival (AoA) using a BLE antenna array on the nRF52833. Our implementation builds on Zephyr...
Hello team, I am currently working on the distance measurement functionality using the development kit (nRF5340 and SDK: v2.9.0). At present, the distance measurement runs...
Hi,
Right now I'm looking down at the nrf52840 datasheet, because I would like to do a project with such MCU, but I got to the part of the integrated DCDC converters and...
Im working with:
-Windows Nordic Connect for Desktop App v5.20.
-Direct Test Mode v2.5.0
-nRF54L15 flashed with ncs v2.9.0 direct_test_mode example
There is currently...
Dear team, in my design I'm using MCUBOOT to perform FOTA DFU over BLE and I need some confirmation about the building process to be sure to do all the step in a properly...
Hi!
I'm migrating my development environment to arm-based Mac. I succeed to install nRF Connect for Desktop app for aarch64 architecture, but struggling to get Bluetooth...
Background
Our device uses the CONFIG_LTE_NETWORK_TIMEOUT option from LTE Link Control, which by default is set to 600 seconds (10 minutes). I haven’t found any specific...
I have included app_fifo files in the group as well as in the linker along with enabled APP_UART in Configuration wizard of sdk_config.h still the error persists. Please ...
I've been trying to find resources on the possibility of securely limiting BLE connections to only 'signed' applications. I understand that this goes against the general concepts...
Hi all , I using timer 0 to count from 0 to max value 32bit . In my code :
If I using NRF_TIMER0->TASKS_CAPTURE[1] = 1; for save counter value to CC register . It run...
Hi Everyone
I am working on nrf52832 with sdk 14.0.0 on iar IDE. TWI and SPI separately working fine in buttonless_dfu then i merged SPI and TWI in buttonless_dfu itself...
I am trying to update an older application use the spi_5W_master and receive the error: (SDK11, using S210 softdevice)
:RTE\nRF_Drivers\nRF51422_xxAC\spi_5W_master.c(346...
Hi,
I'm trying to advertise 2 packets simultaneously, connectable packet using the soft device and a becon packet using the timeslot. I'm using nrf52 SDK 14.0.0 and SD132...
Hi I am doing some research for my paper, but It is my first time to use NORDIC board.
With broadcom and bluez combination, I could check data packet in l2cap layer, but...
Hi All,
I have a question about NRF52840 power consumption. It is not very clear from the datasheet what is the power consumption if I'd like to use only one of the DC...
Hi everyone,
Preface: I'm an educator and my students are familiar with the Arduino IDE, so I'm using that in combination with the sandeepmistry/arduino-nRF5 core.
Our...
Hi
I am developing nRF52832 wake up solution using LF (Low Frequency).
Initially, I develope it without sd_app_evt_wait .
After that, I am used sd_app_evt_wait to reduce...
Hi, I'm writing this because of nRF52840 booting error
I got this product today and It worked well, but after I downloaded one of the example's ~DEBUG.jlink file to the...
I may have a massive misunderstanding here....
Using nRF52, SDK 14.2, Ant S212.
I use a background scan to discover devices on channel 0, with a beacon on channel 1. ...
My isp (Internet Service Provider) doesn't provide ipv6. Now how do I send ipv6 packets (BLE over ipv6 packets).
Updated: I have an Nrf 52832 and I want to send access my...
Hi at All,
I’m currently working at a design using nRF52840. It’s extremely space sensitive and actually I’m not able to place all the needed parts to the PCB.
Therefore...
