Hello,
I have a legacy project that is using nrf5 sdk v17.0.2. I need to add the BLE DFU functionality to this project based on the nRF52840. Are there any examples on...
I was doing some developement for a custom board on NCS v2.9.1 when i noticed some of the changes i was making in my prj.conf weren't being set in the application. My impression...
In my circuit I have a MOSFET which disconnects the battery. There is a GPIO pin which turns this device on and I'm using regulator-fixed to drive it during start-up. A short...
We are currently using ncs 2.9.0 on an nRF5340. We use the BT_HCI_OP_VS_READ_VERSION_INFO to determine at runtime what version of the BLE stack is present. This information...
Hi I'm trying to load a custom board with nrf9160 with the Serial LTE Modem, and route the AT commands to the UART from a coprocessor (ESP32C3) I have followed the guide on...
Hello,
we have a working system on the nrf9161 that works without zephyr. We have our own secure firmware that successfully uses the cc310 after we start the actual application...
Keep hitting my head on this inconvenient workflow.
Edit build config
Select target custom board
Build config
All OK
Edit config again
Target board has been...
I donwloaded the iOS nrf toolbox. I found that the app converts the glucose measurement to KG/L and not to mmol/l? The reading on the glucometer is in mg/dl so when I multiplied...
Hi,
I am trying to get my mesh running on the nRF52 Preview DK but calling
SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, NULL);
will break my program...
I am using nrf51422 and ble app uart as my example code and trying to connect to my ios app nrf toolbox by enabling a static key for the pairing process. i have read all the...
After installing the Master Control Panel 3.10.0.14 (x64) on Windows 7 Professional, uninstalling JLink V5.02a (which MCP really does not like) so it uses V4.98c, and realizing...
Hi,
I have a program that it works fine with nRF51-DK, but I want build a PCB with the Waveshare Mini nRF51822 module.
What do I need to program this module? With the...
Hello
When refering to the documentation its stated:
"The DTM application is stand-alone. Therefore the S110 SoftDevice must be erased in the nRF51822 device. "
Is this...
when i download the 7.0.0 softdevice and the demo project "Nordic\nrf51822\Board\pca10001\s110\experimental\ble_app_uart" to my nRF51822 board,it works well,but use the 8...
I have changed some where of bps demo.one of is i use the app_timer_create() api creat the time use to send digtal periodicity,but after changed the nrf51822 could connect...
Hello Everyone,
I flashed the nrf51DK by using the basic blinky example after that i tried to flash the UART example program it is displaying programming is done, but still...
Dear Nordic Developers
I'm using ble_app_uart example with PCA10028 development board. SDK version is 8.0.0.
I'm trying to program the PCA10028 board for having a static...
Hello Everyone ,
I am using nrf51DK i have compiled the basic blinky program it get downloaded properly and also i saw the output after that i compiled the ble_uart_example...
Hi,
I'm searching a way to create a function which would be a timer function (so, this function will have an int number as input parameter), and during this delay, I would...
On this question I read that S110 is blocking CPU a lot during advertising/connection ( devzone.nordicsemi.com/.../).
On this other question they say that you can change...
