Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hello,
There's lots of questions and back and forth talking the nrf51 SDK both on here and on other sites, about the requirement for a product key to access and download...
Hi,
Using nRF51DK with softdevice 8.0 and sdk8.
I found the max number of whitelist in "ble_gap.h"...
/**@brief Maximum amount of addresses in a whitelist. */
#define...
Hi
I want to get the number of broadcast data.i try it as follow:
But i can not get the BLE_EVT_TX_COMPLETE event. Why? can you tell how to get the number of broadcast...
Searched -- without success -- the SDK docs extensively for access to the Transmit Window Size.
Wondering if there are ways we can manipulate it, and query the current...
Hi all,
I want to know how long it takes for NRF24LE1 to wake up from low power mode, especially in these situations:
1) Wakeup from pin voltage level , from Register...
Hi~
I am trying the example code of [--app-button-example-master--] from here... github.com/.../nrf51-app-button-example
for understanding button press features. I did...
Here i have made an UART0_IRQHandler routine. When i try to send some 50 bytes data through UART using PC tool here its receiving bytes, but it only receives 1st 6 bytes which...
Hi Everyone,
I'm working on adding DFU on my project and here is my setup:
Softdevice = 7.1.0
SDK = 6.1.0
DFU Bootloader = Keil compiled from SDK 6.1.0
MCP...
I'm having a bit of confusion understanding how the nRF51 Series Compatibility Matrix works.
I have a QFACA10 development board running my software perfectly, but when...
The nRF51822 Bluetooth Smart Beacon Kit User Guide (nRF51822-BK-UG) mentions an iOS project contained in the zip file nRFBeacons_iOS.zip. Where is this file? I cannot find...
Hello all,
I'm trying to save the service context with the Device Manager on the Central side. But I don't understand the implementation on how to do this. But no information...
I'm trying to adapt the BLE_BAS_C library to perform discovery and read/write operations for a custom service. However, when I change the UUID that I register with ble_db_discovery_evt_register...
i used this function to send data to my ble device ble_nus_string_send.this function sends ASCII values. and when i pass this function hex values it converts them into ascii...
Hello,
I was using wiringPiSPI() to connect via SPI and so i was using wiringPiISR function to create an interupt handler that will do callback to the user suplied function...
