I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Hello,
i am working on an app using Android to read and write an NDEF record using SDK 14 type 4 tag.
I start the process by reading the record with the following Android...
hw: nrf52dk
sw: sdk14.2, ANT/BLE "multiprotocol" HRM app example
I tried to build and run ANT/BLE HRS relay example from SDK14.2 WITH NO CHANGE IN CODE, but it doesn't...
I used two PCA10040 boards to test the UART serialization function with s332 softdevice.
I add my ANT_PLUS_NETWORK_KEY and build the examples "experimental_ant_ble" is working...
Hi, I have a strange problem. I am new to nRF IC's.
I recently took a new job...the person who wrote the code for our nRF51422 lost some source code in the process of changing...
I'm trying to create a HID bluetooth device with multiple connections to centrals. Looking at the ble_hids service implementation, the on_connect event handler sets the connection...
Hello!
I'm looking to build an application on nrf52840 DK that collects multiple sensor values and transmits it over Bluetooth. For now, I don't have a bluetooth application...
Hey I'm doing some SPI transfer in response to a GPIOTE in event. I'm targeting the NRF52840 and kind of went with the following answer:
https://devzone.nordicsemi.com...
Hello,
My setup is pca10040, sdk 14.2, s132.
I have tried firstly the blocking mode function and it is not reacting. After that I used SAADC module in a non blocking mode...
Is it possible to use the mbr, currently inside the softdevice, without the softdevice? Can we use the combination MBR/Application/bootloader? So we have a lot more flash...
I'm developing for the NRF52 DK (nRF52832) using VisualGDB (which uses SDK v11.0.0).
When completed my program is supposed to read data from sensor (via I2C), store it in...
Hello ,
is the NRF52810 surpport LE long range? is the mainstream mobile phone surppot LE long range? if i set the nrf52810/nrf52840 to be LE long range mode, and then ...
I am developing a product for indoor positioning and some thing else.
I want to know that how many beacon device can operate in same place.
As I know, beacon devices can...
All,
I already run BottonlessDFU example successfully after refer to below link. What's more, I added BAS and DIS service to Bottonless DFU example, and after use nrfutil...
