void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
Hi,
I would like to have a recommended supplier for the 32MHz crystal. I have seen the specification for the crystal. But from my experience it is a bit more complex than...
I followed the guide of this and when I opened the project " BLE_Gateway" ,it showed that the "spi_slave.c","softdevice_handle.c"and "ble_advdata.c" file couldn't be found...
I can not compile the example project 'ble_app_uart_s132_pca10036' ,in nRF52_SDK_0.9.2_dbc28c9\examples\ble_peripheral\ble_app_uart\pca10036\s132\arm5_no_packs.the error given...
I have a fully working project that uses the HomeKit SDK 1.0.0 from Nordic Semiconductor.
In order to be compliant with Apple specs I am trying to upgrade to version 2.0...
Hello,
I enabled debugging in keil v5 for the nrf 52 and I am debugging through UART for the ble_app_proximity and viewing the messages in putty. The messages i received...
hello everyone,
I was trying to turn off nrf51822 on some condition. So i thought i will use systemoff mode register to do that.i am attaching code snippet of what i am doing...
I am trying to build the ble_app_hrs using gcc. It seems to build okay. I can program it to the device. When I press button 0 or any of the buttons the leds does nt light...
Hey All,
Just trying to get some advice/examples on how to incorporate notifications into a Custom Service on a nrf51 Dk board using gatts. I have found a couple of examples...
Hallo everyone. I'm working with the processor nRF51422 with S210 softdevice and I would like to ask you if it's possible to drive results of LPCOMP to a General-purpose I...
My goal to build a device that can connect to phone with nRF8001.
I am using nRf8001 Development kit. My prototype uses TI msp430 with the nRF270 board in the kit, and I...
Hello,
I am using a Windows 7 VM (VirtualBox). I can flash my NRF51 DK using nRF Go Studio just fine.
When I open the Master Control Panel (3.10.0.14), I can see the device...
Where can I find a description of the different nRF24 part numbers? Specifically, I am interested in learning which part numbers correspond to OTP variants. Thanks!
Hi guys, I have an application, where I need to change the role of the S120 softdevice on demand. So, the application boots into central role, reads a couple of BLE sensors...
