Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
i made this project to try to create RSC service on arduino
developer.bluetooth.org/.../runningspeedandcadence.zip
unfortunately the server starts but i'm not able to...
See attachment - enlarge if it's too small. How can I get nRF Connect on my Windows 10 laptop to bring more than 20 characters, and also print in text (instead of hex values...
I would like to know the part number for the Side facing RGB LEDs used in the Nordic Thingy 52. I couldn't find the Bill of Material for the Thingy 52.
Hi. I got TCA6424A IC which communicates through i2c. I tried to use that with nordic but it doesnt respond. I used simple twi scanner application which should print address...
Dear nordic employee
My 52832’s GPIO control the external 32mhz crystal‘s power，
when the 52832 work in the sleepmode ,I cut the 32mhz crystal'power
then when I want...
Hi I have a problem with TWI (the slave part), that is, we can only receive on nrf52840 8 bit, there is someone who knows how to do so you can receive 16 bit, we have taken...
Is there possible to get timer period shorter than 12us with nRF51 and SDK 14? "timer" example with PCA10040 works correct, but with PCA10028 not. When set timer period lower...
When I go to build any of the nRF SDK BLE examples, I get linker errors that app_error_handler was not found. I now copy-and-paste a boilerplate version of that into the code...
Hello,
I'm currently trying to OTA update the firmware of my nRF52832 DK, I use the SDK 12.3.0.
I loaded the BLE Secure DFU Bootloader in the DK, it's advertising as...
Hello, i use nRF5_SDK_12.3.0_d7731ad. I took this tutorial https://devzone.nordicsemi.com/b/blog/posts/getting-started-with-nordics-secure-dfu-bootloader and according to...
Hi, Guys,
I am using nrf52832 for our product. Recently I updated stack and sdk from s132v2/sdk12.1 to s132v4/sdk13. However, I see a new characteristic under Generic Acess...
Hello,
I'm trying to run the example ble_app_uart using nRF52840PDK and iOS 11.
The device appears as Nordic_UART but when I connect, nothing shows up. The following screen...
Hi! Compiler errors are popping up when working on nrf_drv_rtc.c while log is enabled for this nRF module. I see that the problem is any log statement that contains EVT_TO_STR...
Good afternoon,
I have been doing some tests with the nRF SDK for Mesh v1.0.0, and have a question regarding it.
I'm using a fw based of the Light Switch example, to...
