Hello everyone,
I am using the great platformio toolchain that supports the mbed framework so far. I am still a newbie to it however.
I want to be able to use both the...
Hello!
I have a device with nRF51288. And I need to fill technical specification with the following parametres: operation freq., channel bandwidth, modulation, number of...
Hello,
Does anyone have a suggestion for a production programmer for the nRF24LE1 One Time Programmable version? I have been able to program the units with the nRFGo Studio...
GOAL: To send one 20-byte data packet from an Android Galaxy S5 to nrf51822 and send three 20-byte packets from the nrf51822 to the S5 in a single connection interval of 10...
Hello, I have looked into the compatibility matrix and I couldn't find any clear answer about if the NRF Beacon Kit is compatible or not with the S130. Does anyone tried to...
hi:
now.i have a development board(nrfgo motherboard).there is a debug port on the board.i think it can be debugged on the keil.if it can.what driver or others i need.thank...
This is what I got after upgrading my nRF51 dongle firmware.
It always times out.
I didn't somehow got one of my J-Link Lite upgraded, but couldn't repeat the process...
Hi everyone,
Maybe my problem has already been solved in another discussion, if so, I haven't found it yet !
I'm programming on a external board using nrf52832.
I...
Hi folks,
What's the maximum interrupt frequency the nRF51822 can support? I am looking to do an interrupt burst of about 4000 interrupts at a rate 2MHZ or 4MHz. In the...
Hello friends,
I am trying to flash a nrf51 dk with keil5. When I try to flash it with a multilink universal I get this error:
My settings are the following:
...
Hello !
I have a big problem !
I explain : am using the NORDIC nRF52840 board (as slave), to answer to a microcontroller (the master), using SPI. My nRF52840 has to simulate...
Hello.
Some months ago I open this thread .
Yesterday talking with one member of android team, told me that the problem with "pairing/bond" persists with few Huawei phone...
Hello everybody !
My code is based on the code of the "ble_app_template" to which I added my own custom service composed of 4 characteristics sending notifications. Notifications...
Hello Nordic developer, I'm asking my self if it's possible to use a task of one timer like STOP TASK or START TASK as PPI event ? For example, like that :
I expect that...
how can i program in nRF 52840 UARTE. i want to communicate with other serial device using nRF 52840 UARTE communication (send and receive data).
can you send me the snippet...
Hi,
I am developing an ANT+ embedded device (nrf52832, SDK14.2) , that (among other things) acts as a BSC receiver. I have a BCS sensor that is seen in Garmin Edge as 136150...
I want to transfer data using UART to BLE by Baud Rate 19200(using nRF51822).
Transfer data speed need to achieve 2KB/sec up.
How can I do it successly?
Thank you...
I noticed that you have a branch called feature/v6-upgrade for pc-ble-driver. Is that branch usable for 52840 and s140?
By usable, I mean it can be mostly usable and we...
Hello,
I am following the PPK Get started get started of the PPK board.
I am developing on the NRF52-DK (Rev 1.1.0 2017.23) - nrf52832 My SDK is the nRF5_SDK_15.0.0_a53641a...
Hello everybody,
I am using sdk14.2, s132 with Nrf52832. I want to define the pin of the NRF52 as the input and decode the incoming pwm signal. For example, I have a signal...
