I am working on "nRF51_SDK_8.1.0_b6ed55fnnn\examples\ble_central_and_peripheral\experimental
\app_s130_demo\pca10028\s130\arm4" project .
In this project,in which variable...
Or is there any LCD you could suggest that doesn't need that much code? Simple numeric 2rows would be enough. Want to use it with the nRF51-DK to display some measured valued...
I would like to develop my own central device to communicate with the RedBear Arduino shield. The RB device uses a from of UART communications to send data to/from Android...
I was wanting to use a nRF24L01 with a breadboard but its pin-out didn't allow it. A solution then occurred to me based on parts at hand. I wrote it up with instructions and...
Hello. Can I get a literature to the nRF51 series?
I need a full abstraction of the nRF51, like a book or other information, it's structure schematic of build-in modules...
hts, HTC phone, nrf tools HTM, nrf51822,
every time when it's power up :
the once connect: error code 0x7A cann't read characteristic and 0x14 state change.
the second...
Our company needs wireless temperature sensors (can be externally powered or battery operated) and transceiver with 4 channel analog outputs. It has to be finished product...
Hi As part of attempting to write code for self testing I'm trying to measure the HFXO frequency using the LFRC (we don have an LFXO) I'm expecting that the measured HFXO...
I use nRF5340 audio DK,iso_time_sync example, can successfully send BIS data, then I use DK as controller, bumble( google.github.io/.../index.html) as host and it fails to...
I am reaching out to seek your guidance on a development project involving the nRF52840 and Semtech SX1262 LoRa transceiver.
We are building a marine crew monitoring and...
Hi,
The following URL does not include nRF54L15, is it supported?
https://docs.nordicsemi.com/bundle/ncs-3.0.0/page/nrf/samples/openthread/coap_server/README.html
...
nrf52820 custom board
nRF5_SDK_17.1.0_ddde560
s112_nrf52_7.2.0_softdevice
secure_bootloader_ble_s112_pca10100e
I tried to incorporate ble dfu to my application but...
Please refer to the link below. How can I configure the Commission Flow according to the requirements?
www.matteralpha.com/.../how-does-matter-qr-code-work
Dear devzone，
Based on ncs2.9.1 and nRF54L-DK(v0.9.2), add in the prj.conf of the peripheral_uart example:
Compile and burn to nRF54L15-DK, the program does not run, and...
Hi,
We are testing connection resilience on our nRF9151 product. Generally, LTE-M connectivity (Germany, on Telefonica and/or Telekom) works fine.
However, under certain...
My product currently has DFU (Device Firmware Update) functionality enabled, but I want to allow firmware updates only after receiving a specific command via BLE. This is...
I am trying to use the HCI UART application with channel sounding enabled and communicating with an external host. I was able to perform all CS procedures, and when it was...
The direction_finding_connectionless_rx **works fine with NCS v2.3.0**, but with v2.9.0 get's a link error on dts instance for nrf52833dk:
I have top view knowledge of the...
Dear Nordic Engineers
I developed a PWM function to drive the RGB LED. Then I found a problem, which is w hen I used a PWM signal of one channel to control the RED light...
Hi all,
I want to fully understand the concept of Bluetooth protocol using nrf52811. Any advice will be helpful for me!
First, as I understand softdevice is Bluetooth...
Hello community,
I recently was trying to evaluate the GC9A01 display from waveshare, I used the github source code as the base code to test this. Attached the link below...
As shown in the figure, MCUboot has a boot_go_hook function. I'd like to define this function in my own project and compile it into MCUboot. Since I'm using single slot DFU...
