I am try this at nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
Firt I connect to Android device and keep one whitelist.pp_addrs and one whitelist...
Hi,
Parameter uint8_t ble_gap_scan_params_t::filter is present in the documentation, but not implemented.
Checked for SDK 5.2.0 and 6.0.0.
devzone.nordicsemi.com...
After I get a Disconnected() event, I want to start scanning again, therefore try to call StartDeviceDiscovery() again.
IsDeviceDiscoveryOngoing was checked before.
The...
Hi, I wanted to ask a question regarding sending data.
I currently have external memory that will send out serial data (SPI) to the nordic microcontroller. I have saved...
Recently, I try to programme nRF51822 DK communicating with nRF2401e1 DK,unfortunately，which does not success. With setting radio configuration: TXPower,frequency channel...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
E:\BLE\work\nrf51_sdk_v6_0_0_43681\nrf51822\Board\nrf6310\s110\ble_app_hids_keyboard
SDK 6.0.0
Softdevice 7.0
When I connect to Android 4.4.3 device(Nexus7 II) will...
Hi folks,
I have a 2MHz clock (call it DRDY) coming into my nRF51 on one of the GPIO pins (call it AFE_DRDY). I need to read an external AFE chip on every falling edge...
I have a project where specification requires disconnecting immediately after sending a response to a BLE read request. I'm using authorized reads.
Currently, I'm using...
Hello,
I am measuring 5~6 mA of current consumption in standby mode, even when not broadcasting/connected. Why is it so high?
Aditional info:
I am using a custom...
I am using IAR workbench. Using softdevice s110 Version 7.
I have created a bootloader at memory address 0x3A000.
My application sits at 0x16000.
My application checks...
I used the sample code from nordic with nRF51822. DTM works fine. sensibility test gives me 0% on the 3 channels. Perfect.
Then I copied and paste into my code, calling...
I'm compiling and running correctly but the Keil software program for St- Link does not work I have . Have a different method to compile and install nrf51822 ?
on iOS 9 beta 5, ANCS doesn't work.
Steps to reproduce:
On iPhone, Settings -> Bluetooth
Tap to connect and pair
Make a phone call on another device
no caller...
Good work,
I am trying to control with android i nrf51822 But I have a problem. Ten LEDs After connecting the device with Android when I press the off button or "device does...
redbearlab nrf51822 led controller with android.nrf51822 with android connected.But led on off Device does not support uart.Disconnecting.
How solving is the problem ?
I wrote code usenig de Development Board 10028 (nrf51422).
I bought in aliexpress This model link text
The first question I remember There is almost no difference between...
I have a project, where I try to trigger an interrupt when I get a low-to-high tranistion and high-to low transition.
My setup:
-nRF51DK
-SDK8.1
-SoftDevice 8...
I'm looking at the ble_app_hrs example and I'm confused about how the drivers are able to differentiate between events originating from various services/characteristics. For...
The JLINK is costs hundreds of dollars, the STLINK is less thank $20 USD (available on ST's Discovery boards). I would really prefer to use the STLINK. Is there a way to program...
