Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
From the datasheet, the On mode with all blocks idle draws 2.6 uA.
In my code for the PCA10001, I immediately set:
void sleep(void)
{
__SEV();
__WFE();
__WFE();...
I was going through online material all of which mention that the profiles and protocols (GAP,GATT,L2CAP) i.e. the host for a BLE implementation is a software stack rather...
Hello - I have gotten blinky_example up and running in eclipse using the SDK 5.2, nan-29, and some additional google-fu.
Now when I press debug and the play button, it...
I am trying to use nRF UART app and nRF8001 chip. But I cannot change the device name. I intend to change the device name after nRF UART app detects the device. Plus when...
I'm trying to create a method so a users can initiate an OTA update from a paired device. To that end I've written something which is supposed to invalidate the data at the...
I'd tried some first steps using nRF Sniffer on a linux host.
Within sniffer_uart_protocol.xlsx I read something about the Uart packet format et cetera.
I'd programmed...
I am trying to get ble_app_beacon exampel working on the PCA10001 on my nrf51822 working. However when I simply run and reach APP_ERROR_CHECK(err_code) inside "advertising_init...
Reading through the nRF51822 Beacon reference design it states that there are Keil ARM project files available. Does this mean that the example code given after purchasing...
Hi all。
I am programming a nRF51822 chip, using the S110-nRF51822_6.0.0 soft device,download ble_app_hrs.hex。
I used app name "nRF Utility".I can connection nRF51822...
Hi,
i have some more, for me fundamental, questions and i hope some one can help me :)
1.) can i use the advertise function whenever i want or only in connection interval...
Hi All,
can any one please share information related to this
1)please explain clearly about channels and pin?
2)can 2 gpio pins hooked to a single gpio channel?...
I'm not sure if this belongs properly here - but I wanted to send out a thank you to Ole Morten.
I saw your reply in http://www.funwithelectronics.com/?id=168 and this...
Are there any plans to create a Google Glass compatible app like the nrf UART app? I'm trying to link a microcontroller with Google Glass via your bluetooth low energy module...
I'm using the Arduino SDK but I don't think that should matter for this comment. I think a small change to some of the lib_aci functions would make it easier to use them....
Hi,
I'm using an arduino uno with a readbearlab shield with v1.1 to send sensor data to a android phone.
Using a timer interrupt I try to send data every 0.1 sec (10hz...
